Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
I am using fstorage functions in the ANT broadcast RX project.
I am doing the fstorage write function when the ANT device is connected (Inside RX EVENT of ANT event...
Hi
I need to change the default mtu size（peripheral device）, but it always 23，unless phone requeset mtu size.
ncs2.7.0
nrf54L15pdk any peripheral demo
I need this...
Hi
I know , there are several threads on this subject, but I would like to know if there is a sample that works out of the box on the thingy91.
If not, is there an alternative...
Some time i got this error msg
error] [ Client] - Encountered error -105: Command connect_to_emu_with_snr executed for 40 milliseconds with result -105 ERROR: Unable to...
Hello, I have a question regarding the watchdog with secureboot.
I just added watchdog to my app, but I'm worried that when I DFU the HW watchdog will trigger during the...
Hi,
I have tried to look through the forums but I cannot find exactly how the nRF Connect -> Power Profiler application is able to get/obtain the device SN?
In the log...
Hello, we have a project with nRF5340 and SDK v2.6.0, and we can not obtain the logs from the network core b0n bootloader , but we do receive properly all the other logs....
SDK:17.1.0 application: ble_app_uart(+ble_app_buttonless dfu service) bootloader:secure bootloader pca10040e_s112_ble Background: There is only one key(pin:31) on the PCBA...
Hi there, I am trying to use shell with the USB and logging with RTT. Additionally, UART0 async is used to communicate with sensors. Here a snapshot of the proj,config:
...
I'm developing a custom board with a uBlox NORA-B121 module, which contains an nRF5340. The board has a Microchip MCP2515 CAN controller, and for some reason, I can't receive...
I am porting an application from NCS v2.3.0 -> NCS v2.4.0. My application runs in nrf5340dk_nrf5340_cpuapp_ns with NSIB and mcuboot. The mcuboot uses external flash for the...
I have Thingy:91 dev board. I have flashed hci_lpuart sample to nrf52840 and successfully ran lte_ble_gateway sample. Now in my application I want to connect to the same hard...
Hello,
I'm trying to reduce the power conception of my custom board with a nrf52840 and a 4g modem on uart.
For this test, I reduce the code to a loop (modem is off...
NRF52840 running 17.1 SDK and using QSPI interface to erase a block of memory from AT25FF321A external flash IC.
When we call erase it takes 930 millisec to finish erasing...
I was able to turn ON the Nordic’s BLE DFU over SMP + BLE NUS using Matter Lock sample code successfully.
The “DFU over SMP” is really great but further customization is...
