Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
I have built and flashed both the exercise and the solution. However in both cases I am getting a connected and then disconnected ( Reason 42). I am clueless as to what is...
Hello.
I am currently testing nRF Cloud and encountering an issue. In the "Select a Project" menu, the "Create Project" button is disabled.
Here is some additional context...
I am using SDK 3.1.1. I am trying to use the "sensor get" command with the internal die temp sensor.
In theory, this is all off the shelf software. I didn't write anything...
While running scan & connection tests with NCS 3.2.1 , I encountered frequent connection timeouts ( bt_hci_core: Connection creation timeout triggered ) when using the Nordic...
I'm using the Power Profiler Kit II to measure current draw of an ESP32 board at idle. The PPK2 is connected to the battery terminals of the board (XIAO ESP32-S3) and whether...
Hello, I should like to enquire whether the nRF54L15-DK development board supports both Classic Bluetooth and Bluetooth Low Energy. Having reviewed the relevant documentation...
Dear All,
I'm following the nRF Connect SDK Fundamentals and I have a weird problem in the Lesson 3 exercise 2, section "Adding custom configurations".
The part with...
Hello everyone,
I've been testing the "central UART" with a "peripheral UART" (NUS) examples with two nRF54L15 DKs (nRF SDK v3.2.1 in VS Code). So far, everything is working...
Hello everyone!
I have a question regarding nRF9151 and the new DECT Hello sample. I have installed the newest version of the SDK, a preview of v3.3.0, built and flashed...
Hi!
NCS 3.1 On a custom board with nrf5340 and nrf7002, h ave successfully implemented and tested FOTA over Bluetooth Low Energy with Simultaneous updates for both cores...
Hi,
I'm trying to reduce the power consumption of my Matter Temperature sensor code.
I'm averaging around 90µA of consumption, but I'm confident that can be reduced. ...
Hi,
I’m having trouble getting an ISP1807 (nRF52840) to run on a custom PCB, and I’m hoping someone here might recognize what I’m missing.
Hardware / setup
Module...
Hello, we’re currently facing an issue regarding the start-up of the nrf9151 modem. Its a custom PCB and closely follows the schematic of the nrf9151 DK. For first test SW...
Hello Nordic Engineer,
I know that I can modify #define DEVICE_NAME "device001" in sdk_config.h , but it takes a lot of time to compile and flash the program every time...
