Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
I'm interested in seeing what the NRF debug adapter does, using Jlink
2022.7.111 - nRF Connect for VS Code
I can't get it selected and the documentation is not very...
Hello I'm trying to get the lower consumption with this EvK in power off mode. I was expecting around 0.5uA but the minimum I get is 1.8uA ~ 2uA.
The measure has been done...
hi,
I have a got a nrf9160dk and also a custom board built on nrf9160. I want to know which programmer to use for nrf9160dk first and subsequently can use it for testing...
Hello Nordic Team,
I was priting logs using RTT _LOG APIs
I can able to see timestamp while printing it
<t: 16775755>, main.c, 295, --------------------------------...
Hello Nordic Team,
I have a question out of curiosity.
BEACON debug prints has been enabled. And I am seeing these prints for every 10 seconds.
Below is the log
<t...
for the NRF9160 I have 256KB for RAM
however, only 128KB are available for my software, since it's defined as nr9160ns
how can I assign the full 256 kB for my software...
I use Nordic BLE Mesh example(Light Switch), I want to implement remote control. The following is the topology map, and the publish & subscribe address(Group address) has...
Using a NRF9160DK. SDK2.0.0. Modem 1.3.2.
I have a problem when setting up a new NRF board to run with MQTT with AWS.
When the setup is running, I get LOG <inf> for...
Hi,
we have a unit that needs to go for conformance testing.
The only external interface we have is the nNR52833s USB port (pins 12/13 on QDAA).
Alternatively can the...
Hello,
We're using a nRF52840 with S140 SoftDevice (v7.3.0) for a Central device but we're having a disturbing issue when scanning: a hardfault occurs less than 2 seconds...
Using the pc_ble_driver_py.ble_driver I'm able to subscribe to notifications, but unable to get the values upon connection. The error is:
I do not know how to install...
We have an application where we need the PWM pin state to revert to high impedance between bursts. It doesn't appear this behavior is capable by default. Is there a means...
Hi,
As mentioned in the question, I want to use the external clock as the RTC instead of the internal clock. How to configure it?
Platform: Windows 10
NCS version: 1...
For a fully connected set of node devices in a BLE mesh network, where any node device can send data packets to any other node device via an optimally short number of radio...
