Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi, how to measure RSSI in OpenThread? I have 2 nodes, what is correct state that I have to assign to each node to do transmit/receive test, is it leader and router? or router...
Hello,
We're thinking of powering external sensors through GPIO pins configured as high-drive. The sensors themselves consume only a few milliamps at most, which is easily...
Hi,
I would like to control a piezo driver using GPIO pin on nRF52840 DK.
I've read posts about this kind of application. But still confused about how to set up PWM...
Hello again Nordic Pro's,
I have a mildly modiffied version of ble_app_uart_c that compiles and runs fine on an NRF52-DK board. I am now trying to use the same code on a...
Hi,
I'm very new to the Nordic BLE chips. Sorry in advance for asking stupid questions, but I'm willing to learn! This is my first project for my current job, I want to...
Hello,
I've been trying to run the OpenThread mqttsn_client_publisher example from the SDK. I have also set up the border router according to the tutorial on the infocenter...
Hi:
I meet a strange softdevice assert when I do dfu in nrf52832. There is no info or call stack for this assert, I only get the assert is NRF_FAULT_ID_SD_ASSERT.
Do you...
Hi,
I have been working with the Thingy:91 at the version 1.2.99 but this also happens on previous versions (I do not know which it was but the serial_lte_modem code had...
Hello,
I am facing a issue with the LN service. I am notifying the position at 10Hz and this work well. I have implemented a custom service that allows to send a file by...
Hi,
Just as the title says, I want to use nRF52840 as a peripheral(s140, v7.0.1, BLE_NUS_MAX_DATA_LEN is 244) and using NUS.
And it may pair to a nRF51822(s120, BLE_NUS_MAX_DATA_LEN...
Dear
I got a problem about SES when I create a indepent transferable project for PCA10059.
Background:
I have success to modified a light-swich server from PCA10056...
Dear All,
I need to understand how the Asymmetric Encryption work in BLE. From Nordic, I get to know the following that following are the nrf_crypto frontend modules
...
Hi,
I"m looking for a solution to automatically build the emproject file from the directory *without using any IDE) so that i can export the .hex file and can be used...
Hi.....
I get the following error fault from my device (nrf 52840 with freertos ,using SDK16.0)
the Fatal id: 0x2000B730
what caused Fatal id: 0x2000B730 ?
Hello,
I developed a project based on thread CLI example. Everything works fine but I would like to add more commands to the CLI interface, maintaining the existing Thread...