Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
As the title suggests, we are having issues with BT notifications being throttled.
The function which does the notifications is below:
We loop over sectors of flash memory...
I am trying to replace such a platform and was hoping to use nRF9151 as a starting point.
Is such a platform possible at all with Nordic/Zephyr ?
I have an old 9160 dev...
I am trying to use Edge Impulse ML models on my custom board. I have built my model on EI and downloaded it locally. I followed the sample wrapper code to use my own model...
Hi, I am devolping a sensor system where I am in need of a Tri state GPIO solution
Currently using the NRF54l15DK with all the latest software versions (3.11, etc.), developing...
I am trying trilateration for indoor positioning system with nrf54l15 , using 3 initiators and a reflector I was not able to switch between initiators and also one of the...
Product is a zigbee router.
Use nrf connect sdk 2.4, update it is not an option.
The zigbee join work fine most of zb3.0 coordinator, BUT with an old coordinator it failed...
Hi all,
I'm using aws iot lib and last will topic feature, everuthing works but I have a question, in prj.conf I set my topic with
Is it possible to build this last...
Hello Nordic Team,
We have developed a custom PCB using nRF9151 and nPM1300 . In our setup, sometimes the PMIC powers up and works correctly, but other times it does not...
Hello, I am using Nordic chip 82832 with sdk 17.1.0 and SoftDevice s132. I am facing an issue where a specific requirement requires my advertisement interval to be specifically...
Hello,
we would like to use the LPCOMP on the nRF54LM20A, but there's some confusion on which GPIO domain can be used.
According to the overview block diagram , LPCOMP...
Hello,
I'm working on a custom Zigbee End Device application where I want do some modification of the device announcement message. I've used NXP's Freescale Beestack Zigbee...
In Nora B-206(nrf54l15) not able to use port 1 pins 2,3 (P1.02/NFC1 P1.03/NFC2) as normal GPIO. TRIED :
& nfct {
status = "disabled" ; // Disable NFC to free P1.03 for...
Hi,
I'm using a custom code I developed to save all console logs to an SD card based on the Zephyr architecture. I originally developed it for the Thingy:52 and have also...
Under the old `nrfjprog`, it was possible to check whether the modem firmware matched a particular release by running `nrfjprog --verify mfw.zip` (see )
This is no longer...
Hi Nordic support:
We previously submitted a case about OTA testing in CMW500 connection mode. Following is that case:
We tried OTA testing with the CMW500 connection...
