Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi
I have a simple application which is comprised of a notification from peripheral to central , and a write without reponse from Central to peripheral.
In windows every...
Greetings,
We are using a nrf54L15 and trying to use the GRTC Clock output functionality as described in 8.10.4 of the datasheet.
We need the most accurate clock output...
In the next step, I compiled the “Serial LTE Modem” firmware example from the examples folder and flashed it onto the nrf9160DK.
The “Serial LTE Modem” application works...
Hi,
I use the nRF9160dk and I want to use nRF9160's internal flash which has 1MB flash to store a few data. But I cannot find any guideline about using nRF9160's internal...
Good evening, I have recently purchased an nRF52 development kit which I would like to use for my project. Currenty, I would like to provision external devices using this...
Hello, I have a custom board that was designed for me, but based off of the Acconeer XM126. It is very similar with a few minor differences. The person who designed it has...
I'm developing based on the Nordic Academy example here, but I noticed that when transmitting a large amount of data, something is limiting the amount sent by the NRF52832...
Hi,
It seems that CONFIG_IEEE802154_NRF5_UICR_EUI64_ENABLE is not supported on NRF54l15.
Where should be the custom vendor EUI64 value stored?
Only the FICR?
Thanks...
Hello, I recently installed nrf sdk but I have trouble getting through getting started phase. I'm using ubuntu 24.04 and created workspace environment using CLI. Below is...
Hi I'm encountering an error while building Lesson 8, Exercise 1, Step 3 using the nrf7002dk/nrf5340/cpuapp target board. Below is the error message I received:
The same...
Hi, I have a BLE device in Observer role - it will constantly scan for Broadcasters broadcasting our unique UUID and put these scanned devices into a Ring Buffer.
The reason...
Hello,
I've encountered a condition where k_sleep(K_SECONDS(1)) never returns. Here is minimal example, reproduces both on nrf9160 and nrf9161:
Hangs up after printing...
Hi!
I am looking for a NRF52840+OpenThread+Azure IoT Hub SDK solution. Here is what I did so far. Nothing helped:
Thead CLI Example on NRF52840 + Border Router on...
Hello Nordic Team, We are currently using nRF52833-QDAA SoC for developing a new project that incorporates geofencing functionality using BLE.We . We tried using the example...
WE are working on nRF52832 and nRF5 SDK 15.0.0. Currently working on the BLE FOTA process and have successfully completed DFU up to this point. Our next goal is to save configuration...
