Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I'm interested in seeing what the NRF debug adapter does, using Jlink
2022.7.111 - nRF Connect for VS Code
I can't get it selected and the documentation is not very...
Hello I'm trying to get the lower consumption with this EvK in power off mode. I was expecting around 0.5uA but the minimum I get is 1.8uA ~ 2uA.
The measure has been done...
hi,
I have a got a nrf9160dk and also a custom board built on nrf9160. I want to know which programmer to use for nrf9160dk first and subsequently can use it for testing...
Hello Nordic Team,
I was priting logs using RTT _LOG APIs
I can able to see timestamp while printing it
<t: 16775755>, main.c, 295, --------------------------------...
Hello Nordic Team,
I have a question out of curiosity.
BEACON debug prints has been enabled. And I am seeing these prints for every 10 seconds.
Below is the log
<t...
for the NRF9160 I have 256KB for RAM
however, only 128KB are available for my software, since it's defined as nr9160ns
how can I assign the full 256 kB for my software...
I use Nordic BLE Mesh example(Light Switch), I want to implement remote control. The following is the topology map, and the publish & subscribe address(Group address) has...
Using a NRF9160DK. SDK2.0.0. Modem 1.3.2.
I have a problem when setting up a new NRF board to run with MQTT with AWS.
When the setup is running, I get LOG <inf> for...
Hi,
we have a unit that needs to go for conformance testing.
The only external interface we have is the nNR52833s USB port (pins 12/13 on QDAA).
Alternatively can the...
Hello,
We're using a nRF52840 with S140 SoftDevice (v7.3.0) for a Central device but we're having a disturbing issue when scanning: a hardfault occurs less than 2 seconds...
Using the pc_ble_driver_py.ble_driver I'm able to subscribe to notifications, but unable to get the values upon connection. The error is:
I do not know how to install...
We have an application where we need the PWM pin state to revert to high impedance between bursts. It doesn't appear this behavior is capable by default. Is there a means...
Hi,
As mentioned in the question, I want to use the external clock as the RTC instead of the internal clock. How to configure it?
Platform: Windows 10
NCS version: 1...
For a fully connected set of node devices in a BLE mesh network, where any node device can send data packets to any other node device via an optimally short number of radio...
