NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
hi:
nRF54LM20A_DK board vscode cannot be programmed.
-- west flash: using runner nrfutil -- runners.nrfutil: mass erase requested
-- runners.nrfutil: reset after flashing...
I am writing regarding an issue I am experiencing with two MDBT53V-1M modules (nRF5340) that I have assembled on custom PCBs. Both modules exhibit identical behavior, which...
I migrate an app from NCS 3.1.0 to NCS 3.2.3.
Using mcuboot with a Thingy:91 or Thingy:91X fails.
flash_img_init results in a flash_img_context, which uses ID 2, the application_slot0...
mcumgr disconnecting when i trying to ble dfu .... " Log from nrf connect mobile app"
nRF Connect, 2026-06-16 FYZKS52_E23993 (E2:39:93:7B:81:AA) V 17:16:59.495 Connecting...
We are trying to bring up a new run of an existing PCB design. No changes in the area of the processor, but a different assembly house. The first call inside ble_stack_init...
We're using two nrf54:s, one DK (initiator) and one custom PCB with 2x antennas (reflector)
I've tried adjusting the samples so that multiple antenna paths are supported...
Hi,
I have a question regarding the SAADC timing parameters.
I could not find an official specification for the SAADC power-up time (t_PWRUP). While measuring it on my...
Hi Nordic support:
We previously submitted a case about OTA testing in CMW500 connection mode. Following is that case:
We tried OTA testing with the CMW500 connection...
Hi!
Im creating my own custom board based on the nrf54l15dk board included in zephyr. My board uses both cpuapp and cpuflpr, and has a custom partitioning scheme defined...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
Hi.
Environment : nrf52833, ncs v3.1.1
I am developing device that has PAwR Scanner Role and Extended Advertising for connecting Mobile Phone(nRF Connect APP).
PAwR...
Hello Nordic team,
We are reviewing our nRF54LM20-CAAA (CSP61) hardware design and would appreciate your clarification on several power and RF related points.
DECRF...
We are doing a DFU over BLE with the second MCUboot partition on an external flash. Some times Zephyr can't access the flash after booting, resulting in a bricked device,...
Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
