Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Hi there, I am using nrf connect sdk v2.6.0. I have noticed that after DFU update, I am seeing ble bonding lost randomly on firmware side. I did uncheck Erase Application...
We are running some sample code on the nrf54l15 mcu, specifically: /modules/lib/memfault-firmware-sdk/examples/nrf-connect-sdk/nrf5/memfault_demo_app
We can connect and...
Hi nRF support team,
I am evaluating ST7735 LCD with the nRF82540 development kit. For your information, I am able to set-up the nRF Connect SDK environment on nRF82540...
Hi Sir, I am developing with the nRF52840.
I installed nRFConnect 5.2.1 and the programmer (version 4.6.2), Following the programmer’s prompts, I installed SEGGER J-Link...
SDK version: 3.2.4
I am using two nRF5340 Audio DK boards configured as gateway and left headset.
I added " CONFIG_STREAM_BIDIRECTIONAL =y" to prj.conf and I built everything...
Hello,
I am working with the nRF54L05 and testing SAADC inputs.
I observed the following behavior:
AIN4–AIN7 work correctly as ADC inputs
AIN0–AIN2 show unstable...
Hello,
I have some issues to do work a VL53L1X with NRF54L15 dev board.
Here are my codes
And here is the RTT console response :
Someone can help me please...
After updating from v2026.1.1327 to v2026.3.1484 on Linux, all previously installed SDKs disappeared from the Welcome view — the extension no longer recognizes them. Attempting...
Hi,
Recently I upgraded to nRF Connect SDK 2.6.1 and I was required to enable the GPIOTE in order to build properly. Doing this has significantly increased (nearly doubled...
Hello,
I currently have a DECT NR+ setup running on an nRF9151 based on the newer HELLO DECT sample, using v3.3.0 preview version of the modem. With these comes two files...
Hi,
1. Since I need to use PWM DMA to transfer 320 bytes of data to the PWM for sequential playback. 2. I wrote the following test example to test the nrfx pwm driver, but...
Hey there, we are currently going through regulatory testing for a hazloc product. Our product includes an nRF52805 which is used for BLE provisioning and debugging of the...
Hi,
We are investigating a Nordic BLE DFU startup failure on iPadOS and would appreciate guidance on whether this pattern is known at the CoreBluetooth / iOS DFU layer...
How to change the parity bit on UART on NRF54L15?
prj.conf includes:
CONFIG_SERIAL=y CONFIG_UART_20_NRF_PARITY_BIT=y
DT overlay includes:
&uart20 { parity = "even...
Latest nRF connect for VS code seems to ignore Toolchain manager install dir under certain conditions.
nRF connect output displays " Error: Install directory 'C:\ncs' not...
