Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hi,
I'm trying to create a new project in nRF Cloud (powered by Memfault), but the Create Project button is greyed out. I'm on an nRF Cloud Pro plan and am an Organization...
Hello, on Memfault when I click on this Developer mode switch, it does nothing. It stays off and doesn't turn on. It does this because I have one device in my project that...
I migrate an app from NCS 3.1.0 to NCS 3.2.3.
Using mcuboot with a Thingy:91 or Thingy:91X fails.
flash_img_init results in a flash_img_context, which uses ID 2, the application_slot0...
Hi,
I am trying to configure an Xiao Seeed Studio nrf54l15 sense to transmit pre-processed sensor data via BLE extended advertisements. As the payload is more than 251 bytes...
Hello, when flashing t device using nrf connect icon, it fails to flash with following message
After investigation I found the generated_nrfutil_batch.json (autogenerated...
Hello, I have used nRF Connect for Desktop with the nRF52840 dongle and it works perfectly as far as using the dongle as a central device and a peripheral device (BLE advertising...
Hi,
I am using an nRF54L15 and I would like to explicitly enable the HFCLK (32MHz). I want to use it to drive TIMER00, which will run during the whole application runtime...
Hi,
I am now developing a production programmer and I want to know the behavior of SWD and SCK lines when the nRF52840 is in RESET state.
Cheers,
Kaushalya
We are experiencing an issue with the QSPI driver on nRF54L15 where external flash access stops working after a BLE bonding procedure.
The system works correctly until bonding...
Hi,
Users of our product have reported issues with multiple versions of Hubitat hubs when pairing Zigbee. I'm investigating this issue and have reached a point where I could...
we are using nPM1300 EVK board for an upcoming project we are trying to interface PMIC PM1300 chip with Ambient Scientific processor GPx10 Pro.
It will be a huge setback...
Hi guys, I have been working with a custom PCB based around the nRF5340 that uses the nPM1100 as the PMIC. I have configured it for 1V8 VOUTB output, fixed VBUS, VTERM high...
Hi
Currently I'm evaluating the nRF54L15 die temperature sensor. I’ve taken a few measurements and noticed something I don’t quite understand yet. Perhaps someone could...
We are planning to use the nRF54L15 for a Matter over Thread product, so we are currently evaluating the low-power performance of this device.
According to the nRF54L15...
