Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Dear All, I am developing an application where I need to get the nRF5340 to the low power state, where the chip is consuming less than 10uA when it idle, while using the nRF7002...
I would like to control the RGB LED on the board. I followed the drievr example provided by the nrf sdk, but it doesn't work. As far as I understand, I don't need the signal...
Does the nRF54L15 internal temperature sensor vary, based on the applied VDD voltage?
I'm wondering if this is what I'm seeing. With a VDD of 3V I'm seeing lower temperature...
Hi, I am trying to build my own board based on the nRF9160 DK. I want to keep both the nRF9160 and the nrf 52840 chips on my board. Can these chips talk to each other directly...
Hi Nordic Team,
We are currently evaluating MCUs for our upcoming product, and our requirements include a device with large RAM and ROM , especially larger code space ....
I've seen this discussed a few times before, but haven't seen a great answer on this. It seems to be commonly known that attaching a debugger while using the IEEE 802.15.4...
Hi,
I have been trying to get Periodic Parent Search active on my nRF54L15DK (and also on an nRF52840DK) without success. My approach has been:
Use the OpenThread CLI...
We are currently using the STM32WL5MOC module and are facing a serious issue with LoRa range. The communication range is not going beyond 1 meter, and the RSSI while receiving...
Greetings,
I have set up some tests using the ZTest environment based on the test sample in ..\v3.0.2\zephyr\tests\bluetooth\adv\. for my custom project which has custom...
Hi,
We are considering using nRF54L15 / SDK3.1.1 -> as a wearable device that is part of a Thread network. We also need to do sporadic BLE connections and channel sounding...
We've a nRF9151 DK for which we built the Nordic Semiconductor LwM2M Client sample using SDK 3.0.2 (modem firmware 2.0.2).
We followed all steps listed in https://docs.nordicsemi...
We are seeing network issues in some particular locations. In these areas, the device is unable to connect to the cloud.
Hardware: nRF9160-based board
Modem firmware...
I am running the boot loader with the default name 'DfuTarg' on a Nordic NRF52840 board very similar to the PA10056. I download this boot loader to the board, connect to it...
I am working with a product that uses the NRF52840 MCU and operates as a BLE peripheral.
I would like to know if the Cortex M4 in the NRF 52840 has support for programmable...
