Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi
We currently have products in field test that disconnects from network and never reconnects. It only occurs to a few devices and not all. Restarting the device works...
Hi,
I am using nRF54L15 with Zephyr RTOS in nRF Connect SDK v3.0.2 .
After performing a FOTA update , the device reboots. I need to retain the state of a GPIO pin across...
The 54L15DK has two issues. First, what is the purpose of the 3.9pF capacitor on the reset line? If it's for suppressing glitch signals, isn't the capacitance value too small...
I am using nRF Connect SDK 3.2.1 and Toolchain 3.2.1. The hardware I am using is the nRF52840DK and a custom board with the Raytac MDBT50Q-P1MV2 - which contains the nRF52840...
Hi everyone, I’m updating a Matter attribute:
I’d like to know if there is any callback or event that confirms when the attribute report has actually been sent by the...
Hi,
I'm looking for help with an Android DFU failure involving an old nRF51 Legacy DFU bootloader.
Setup:
- Bootloader: nRF51 Legacy DFU v0.8 (SDK 9.0)
- Firmware...
I am at the breadboard stage of this project using an nRF5240DK and various sensor evaluation boards. Additionally, I have an embedded SDCard connected via SPI. The firmware...
We designed a nRF54L15 custom board with a nRF21540 FEM and nRF7001 Module which are on the same SPI with separate CS pins our device tree is configured for this as follows...
Setup
SDK/OS: nRF Connect SDK v3.1.0 , Zephyr v4.1.99
Board: custom board
Summary I am measuring the time from reset (or power-on) to the first user code...
hi,
i'm learning this exercise and when i build and flash the exercise it works perfectly but then after i see this errors in the terminal
and after that i create the...
When using an onomondo softsim with all security features etc enabled, and using fota on external flash. nrf9151DK. NRF V3.2.3.
How is it possible to make changes to the...
Hi there,
I'm working with the nRF54L15 and using the light_ctrl sample from the Bluetooth Mesh SDK NCS3.1.0 .
I have a set of mesh light nodes, and I configured power_on_up...
Hi all,
I read in some thread (that I am unable to find now), that when stopping the SAADC via STOP Task, the STOPPED event fires (which is expected), however the END event...
When I run the Asset tracker template and look into nrfcloud I see new messages coming in on the terminal and Battery graph set correctly to 32%. I noticed already a long...
