My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi,
I use nRF51822 powered by CR2032 battery. Same decoupling as dev board PCA10001.
Would you recommend different values of decoupling capacitors for battery powered...
I have SPIM working at 8MHz on nRF5340-PDK
I want to increase the SPIM speed to 16MHz.
The errata for nRF5340 states "In 128 MHz mode, SPIM max receive frequency is 16...
Hi Team,
We are using nrf9160-DK. We have tested assert tracker application, where we got the real time GPS data(DK location) we are happy with that. We also tested the...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Environment :
Host : Macbook Catalina
SDK : 16.0.0
Toolchain : ...2018-q2... (the pre-configured toolchain in the SDK)
SoftDevice: (not used yet, planning to use...
Hi, I'm using mesh_ SDK and nrf52840, I want to know whether the relay node in a BLE Mesh can wake up at a specified time to receive or send packets, and sleep the rest of...
Hi,
I am developing a device based on nrf52840 soc, and the rule of my device is peripheral. I want to know, if a connection was established, could my device start the...
Hello,
we are currently in the development of a low power, battery powered device that needs to count slow pulses (period between ~10ms and several seconds).
At the...
I have a custom nRF52840 board that transmits sensor data (using UART) to a PC with an embedded Bluetooth adapter. I have a code on Matlab that works just fine (using blelist...
Dear Sir.
I am using Master SPI to drive 2 slaves.
Both spi are referenced within Interrupt routine ,
When both spi;s slave are referenced I get an error
err = spi_transceive...
This question has been asked before. I have been using the previous threads to cobble together what is below. I opened a new ticket as reopening (really) old threads is generally...
usb hid how to send 6 bytes of data, app_usbd_hid_kbd_key_control can only send 1 key value, I see that app_usbd_hid_kbd_ctx_t can fill 6 bytes, please see
typedef struct...
Hello,
We're needing a lot more RAM than what nRF91 has, does current nRF Connect SDK support parallel PSRAM on Zephyr somehow or is the development on a roadmap?
Hi there, I want to use CppUTest on the nRF52 to start developing my personal and not so personal projects. I am using the SDK for nRF52, with PCA10040's board. For the moment...
