Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I have a GPIO used as input or output. When it's used as an input (99% of the time), I have an interruption on it (falling and rising edge).
When I use it as a output...
This is my first time using Nordic SoCs, so forgive me if this is a silly question. I have a Fanstel BT832X evaluation board (model EV-BT840(832)-V4). I tried the Nordic's...
I upgraded the code from sdk13 to sdk17.
The setting is the same as the original code and there is no error.
However, if I build, the original code is built with the app...
how am i going to merge ble_app_multirole_lesc and ble_app_blinky
I add
into ble_app_multirole_lesc main.c
and it stuck in services_init()
seems like the err_code...
Hi,
I would like to make a system that goes to sleep for a while and wakes up for a short time thanks to the rtc. According to the documentation, the power consumption of...
Excuse me：
PPK2 doesn‘t work，I don't know why，The computer does not recognize the usb port after connecting the USB cable，The indicator light of ppk2 is not on.What should...
Setup:
nRF PPK2 is connected via USB to the port DATA/POWER to the PC
Running nRF connect version 3.7 from ubuntu 20 causing the following issue, when using "Power Profiler...
Hi, I'm having issues programming my Thingy91 via the NRFConnect programmer app.
The Thingy in question has had various applications run on it over time, but the objective...
Hi,
I am currently setting up an MQTT client via the MQTT publisher sample on zephyr.
My mqtt client is a NRF5340 and it is connected via ethernet with my pc and also...
Hello support
I have modified the cli examples and run into "undefined reference to `nrf_cli_uart_transport_api'" linker error.
The error message is
Compiling file:...
Here's my setup:
1. RPI4+nRF52840 dongle as OT border router
2. nRF5340DK running CoAP client example application
3. Wireshark running on Mac OS, with nRF52840 dongle...
Hello!
I'm trying to develop a mesh network and I've been building on top of sensor example, which has been very useful since I'm reading a few sensors. However I want to...
I am trying to generate ECC key pairs using MbedTLS on Connect SDK.
I found this code block on stackoverflow and validated from mbedtls/programs.
"mbedtls_ctr_drbg_seed...
I was trying to evluate the Periperhral ISO server, however with a NR52dk, but it returns ENOTSUP.
Bluetooth initialized Unable to register ISO server (err -134) [00...
Hi all
I am developing a proprietary radio protocol application using the nRF52805. I am not using a softdevice. Instead, this is all done by accessing the radio registers...
