Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I've been trying to set up UART communication with external device using uart3 instance and have so far failed.
The scenario requires sending 5 bytes to the device...
Hi!
I'm trying to portnRF7002 QSPI bus driver for one of the NXP MCUs. Communication with nRF7002 under Zephyr is already established and everything works as expected. ...
I've been testing the littlefs sample on NCS v2.8.0 and v2.9.0 with an external SD card. Initially I tested the sample with an nRF52840-DK and everything worked as expected...
Hi
I compiled an older project using embedded studio and flashed my NRF dongle. Now the USB DFU bootloader seems to be gone.
How can I restore it?
Several links on devzone...
Hi
I am using hci_pwr_ctrl and want to get the RSS (read_conn_rssi(default_conn_handle, &rssi) in a very high frequency. However, I notice when I use 100Hz frequency, a...
HI there,
I've been following the DevAcademy Lesson 5 exercise example on SPI communication to get a nRF9161 DK (as a Master) and an ESP32 (as a Slave) to communicate synchronously...
Is there any othere way than mergehex to merge application core and netcore hex files? I'm not sure if I'm following correctly, but it seems like it might be possible through...
I would like some help with porting the modem library (nrf_modem_lib) to work with my bare metal application. Besides a custom nrf_modem_os.c, I have made a slightly modified...
Hi!
Running LTE_BLE_GATEWAY example on nRF9160DK rev 1.1.3 gives "No HCI driver registered" error together with "Bluetooth init failed (err -19)". SDK/Toolset version is...
To preface:
nRF Connect SDK 2.9.0
nRF9151 DK
Windows 11 PC
Hello,
I have been developing in the nRF Connect SDK for a few weeks now so I am fairly new. I have...
When using the distance measurement sample code on my nrf5340 development kits, LEDs 1 and 2 seem to be working correctly, but LED 3 does not light up when connected. The...
Hi！
I'm working on direction finding. I'm using a nrf52833dk as a beacon, a nrf52833dk and a Direction Finding Antenna Board (PCA2005) as a locator for a bluetooth direction...
Hi All,
I recently received a few dev kit boards that I intended to use for a test fixture we are building. I tried to use it in our test fixture which had been working...
Hello, thingy53 qwicc connect shows 3.2V when pwrd on, yet there is 0v from thingy91x when turned on. Is there some other step needed to get 3.2V? thank-you,
