Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hello,
We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
I am trying to follow the first lesson of https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals
But I have several problems and I can not find out how to fix...
Hello
I am playing with the mesh dfu and the distributor application on nRF52840 DK board
I load the image I want to distribute using mcumgr application on a Raspberry...
Hello
According to Enhanced ShockBurst (ESB) documentation , to stop the ESB module you need to call esb_disable(), but it also says that you need to check if the module...
Hello,
I am modifying an existing custom board with a sensor that requires exactly 1.9V VDD. Previously I was configuring REGOUT0 = UICR_REGOUT0_VOUT_2V1 but I was surprised...
I’m working on a BLE setup where:
A Nordic nRF52840-DK runs as the Central (it scans for devices with a specific name, then initiates a connection).
A Raspberry...
Hello,
We are considering to develop an appliance based on the nRF5340 AUDIO DK.
The nRF5340 AUDIO DK contains the VM3011-U1microphone that is absolute on the market....
Hello,
We’re testing the nRF9160 GNSS performance on our custom PCB and have noticed that, even with A-GPS, the first fix after powering on the device takes significantly...
I am having problems flashing my custom board with a nrf5340 chip. Sometimes it works, sometimes it does not, but more often than not it doesn't work and I cannot figure out...
Hello Nordic Team,
I’m trying to use the nRF54L DK to program an external MCU via SWD , but I’m encountering an error during connection. I’ve already followed this guide...
I'm trying to build the light-switch-app from Matter but I get following errors
I have already tried to reinstall the sdk (I use v2.8.0) and build it just like that without...
After modifying the factory data with the script generate_nrfconnect_chip_factory_data.py, the discriminator and passcode work, but how do I change the value of the Manual...
I am trying to interface an SD card with the nRF9160-DK using an SD card adapter module. My goal is to write the string "hello" to a .txt file on the SD card. I believe I...
Is a TVS diode clamping voltage of 6.5 V acceptable for supplementing the built-in ESD protection of the NRF52840 GPIO pins?
It has been previously established in the forum...
Hi,
I am trying to build an application using the nrf54L15-dk board and want to use the board as a controller. I run the application on the external host but got an error...
