This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
As stated in the title, when I set CONFIG_CHIP_FACTORY_DATA_BUILD to n , the following compilation error occurs.
However, if I keep it as y , the MCU fails to function...
I am measuring latency using the nrf5340_audio with SDK 2.8.0. The measurement points are the analog input on the gateway side and the analog output on the headset side. I...
Hi!
I am using v2.6.1/nrf/samples/bluetoothdirection_finding_connectionless_tx/rx sample, and NCS v2.6.1 for AoA. I made some modification on the rx side to stream I/Q data...
Hi support team,
I'm currently developing a project that requires enabling FCB (for dps to Azure IoT Hub) and LittleFS to store data on an external flash. However I cannot...
academy.nordicsemi.com/.../
The comparison of "increment_count + decrement_count != COMBINED_TOTAL" happens after test_mutex unlock. It is possible that between comparison...
“'\x03\x01\x00\xDB\xDC\x00\x00\xDB\xDD\xFF\xD5\xD1\xC0”An error occurred during the transfer of the bin file, and the packet was returned when the crc was fetched. What should...
Hi,
I'm using nRF52833 DK and SDK v17 to test my applications.
I have to use ADC on nRF52811 SoC, and I wanted to develop a demo on nRF52833DK before implementing on nRF52811...
I am trying BLE+WiFi coexistence on NCS 2.8.0 with nRF7002DK and finding some issues.
First is that it's non-functional. Running the wifi/ble_coex example, there is no...
Hello,
I have a BLE DFU question in this thread that has not yet been resolved.
Since the BLE DFU problem has not been resolved, I have implemented a USB DFU as an alternative...
Hi, I bougth 2 nrf52840 dongle but I dont't know how to use it or program them. So I tried to learn about it looking the getting started guide, this beginners tutorial and...
Hi All,
I have a few nRF9151 that don't want to boot.
I'm not sure if they ever had working modem firmware on them:
Any ideas on how to un-brick?
Thanks!
Ja...
Hi,
I work on a BC805M module (nrF52805) with the sdk17.1.0 & S112. It is powered by a CR2450 battery.
I like to reduce the consumption of the ble_app_beacon exemple....
Hello,
I am using the nrf7002 ek and attempting to optimise the RAM assignment for the project. I have reduced the size of several thread stack sizes as well as the heap...
Hello,
I wanted to reach out about the issue I've been running into regarding the UART Async API. I am having trouble narrowing down what the cause could be.
I am using...
Hello,
I have BLE TX Mask failed to the spec. as shown in the attached image. It seems noise floor is high. TX outpower at +4dBm (see attached CLI). Please advise.
Thanks...
