Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
As stated in the title, when I set CONFIG_CHIP_FACTORY_DATA_BUILD to n , the following compilation error occurs.
However, if I keep it as y , the MCU fails to function...
I am measuring latency using the nrf5340_audio with SDK 2.8.0. The measurement points are the analog input on the gateway side and the analog output on the headset side. I...
Hi!
I am using v2.6.1/nrf/samples/bluetoothdirection_finding_connectionless_tx/rx sample, and NCS v2.6.1 for AoA. I made some modification on the rx side to stream I/Q data...
Hi support team,
I'm currently developing a project that requires enabling FCB (for dps to Azure IoT Hub) and LittleFS to store data on an external flash. However I cannot...
academy.nordicsemi.com/.../
The comparison of "increment_count + decrement_count != COMBINED_TOTAL" happens after test_mutex unlock. It is possible that between comparison...
“'\x03\x01\x00\xDB\xDC\x00\x00\xDB\xDD\xFF\xD5\xD1\xC0”An error occurred during the transfer of the bin file, and the packet was returned when the crc was fetched. What should...
Hi,
I'm using nRF52833 DK and SDK v17 to test my applications.
I have to use ADC on nRF52811 SoC, and I wanted to develop a demo on nRF52833DK before implementing on nRF52811...
I am trying BLE+WiFi coexistence on NCS 2.8.0 with nRF7002DK and finding some issues.
First is that it's non-functional. Running the wifi/ble_coex example, there is no...
Hello,
I have a BLE DFU question in this thread that has not yet been resolved.
Since the BLE DFU problem has not been resolved, I have implemented a USB DFU as an alternative...
Hi, I bougth 2 nrf52840 dongle but I dont't know how to use it or program them. So I tried to learn about it looking the getting started guide, this beginners tutorial and...
Hi All,
I have a few nRF9151 that don't want to boot.
I'm not sure if they ever had working modem firmware on them:
Any ideas on how to un-brick?
Thanks!
Ja...
Hi,
I work on a BC805M module (nrF52805) with the sdk17.1.0 & S112. It is powered by a CR2450 battery.
I like to reduce the consumption of the ble_app_beacon exemple....
Hello,
I am using the nrf7002 ek and attempting to optimise the RAM assignment for the project. I have reduced the size of several thread stack sizes as well as the heap...
Hello,
I wanted to reach out about the issue I've been running into regarding the UART Async API. I am having trouble narrowing down what the cause could be.
I am using...
Hello,
I have BLE TX Mask failed to the spec. as shown in the attached image. It seems noise floor is high. TX outpower at +4dBm (see attached CLI). Please advise.
Thanks...
