Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hi everyone—I'm working with the Nordic nRF54L15 SoC , but I'm struggling to find guidance on using a chip antenna (design and components) . The official materials (e.g.,...
Hi Team,
I’m facing an issue when trying to perform BLE FOTA with a 2 MB external SPI flash (SPI4) as the secondary slot for MCUboot.
My setup works fine when using a...
Hello,
sorry, do not know where to file a bug.
Bug is, that nrf_radio_subscribe_get() and nrf_radio_publish_get() use the wrong offset (0x80) instead of the correct one...
Hi, I’m currently testing the update process via BT SMP on the matter window covering example (NCS 3.0.2, nrf5340). For my test, I created two versions: 1. Project with -DCONFIG_CHIP_DFU_OVER_BT_SMP...
Dear reader,
I am currently working on a project using the NRF54L15 MCU. There is plenty of documentation available for this component, and the reference circuitry for the...
Hi Nordic team,
I'm using nRF52840 with nRF Connect SDK v2.6.0 and using NVS to store RSA key material on flash. The goal is to persistently store a generated RSA key pair...
Hi,
The nrf connect for desktop extension in VS code is not loading anything under welcome, when I try to open the documentation or any other nrf related command it says...
my PCB board uses nRF9161 SiP. The flash chip is W25N02KVZEIR.
on the PCB board, here are the wiring to spi flash chip,
P0.26 to CS#, P0.27 to CLK, P0.28 to MOSI, P0.29...
Hi Nordic team,
I’m currently using an nRF9160 DK and trying to test LTE-M connectivity with a custom test SIM and a network emulator. However, I’m facing multiple issues...
Hello,
I am using the nRF54L15-DK development kit. The peripheral-uart example works well to stream data from the kit to a smartphone using the nRF-tools App. However...
I am trying to use the ADC on an nRF52840DK.
I have configured the two ADC channels in the overlay
I setup the channels like this
and take readings using this code...
Hi, I have faced dificulties calling zsock_poll for ZSOCK_POLLIN with multiple opened sockets, expecially when conbined TCP and UDP at the same time. My goal is it poll for...
So when I toggle the pin high, it gets set to 1.8V. I want it to be at least 2.8V. I did configure the VDD to 3.3V. The VDDIO does show 3.3V, but a pin like let say P1.11...
I have been trying to use the ` nrf\samples\bluetooth\peripheral_nfc_pairing ` sample code on the nRF Connect SDK v3.0.2 to connect to a Samsung Galaxy A16 5G phone.
The...
I bought a tiny board on Aliexpress from HolyIOT. It comes with an nRF52832 and an LIS2DH12 accelerometer. The silkscreen on the board says HOLYIOT-21011-v1.0.
This schematic...
