Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello,
I am using android nrf mesh app as a base app and using the latest nrf mesh library version.
I am taking provisioning trails on inline on-off controller.
While...
Hi,
I have used "write_handler(p_ble_evt->evt.gap_evt.conn_handle, p_rtc_service, p_evt_write->data[0]);" to send data to nrf52832 from nrfconnect mobile app but iam able...
Hello,
For our application, we need to form a Zigbee distributed network and not a Zigbee centralized network. That means that routers need to be able to form a new network...
Hi , I have a problem when I wanted to combine the two examples twi scanner and usbd ble uart together although they work correctly individually I have a MAX30105 sensor which...
Hi all
We're developing an application for nrf9160 with zephyr-sdk v2.4.99-ncs2 and nrf-sdk v1.5.1.
In our project we are required to use a Library which forces us to...
Hello
I want to sampling two analog.. with different configuration and handler.
so I set two channels like this.
and then I call only one sample function like...
I'm working on developing a device using the nrf52832. Currently using the nrf52 PCA10040 dev kit. I'm extending the zephyr/samples/basic/peripheral_dis sample in order to...
When compiling the net CPU with debugging configs such as CONFIG_DEBUG or CONFIG_DEBUG_OPTIMIZATIONS enabled and the resulting hex is flashed to the nRF5340; If then an Ozone...
Hi I am wanting to use the ARDUINO 4 RELAYS SHIELD with the nrf52480 or at least see if its possible.
https://store.arduino.cc/arduino-4-relays-shield
relay data sheet...
I wanna use nRF52820 to make some application development.I wanna a sing-board development kit for nRF52820 ,and nRF52833DK supports development on the nRF52820 SoC and nRF52833...
Hi Everyone This is my first time designing a PCB with the NRF51822. I have designed it using an 2450AT18B100E Antenna and a BAL-NRF02D3 balun. Below is my schematic:
...
There are discussions on WLCSP light sensitivity for nRF5 product, which affects RF, clock accuracy, and low power current draw etc. what about the nPM1100 which clock accuracy...
Is my understanding correct that with VDD supplied and ENABLE = high, having VDD_GPIO floating (i.e. disconnected from a regulated 3.3 V supply) is a valid state? We intend...
hello Nordic
i am working with nrf52840 sdk16.0 s140
i wish to read the UICR register value like this :
but i get this compilation error
since it is a define...
Hello, I'm working the nrfx saadc legacy driver, and despite changing whether I measure Vdd(on the dk) or GND, the saadc output(p_event->data.done.p_buffer[0]) oscillates...
