I am Using SPI4 in nrf5340 and I am trying to put SPI in low power mode when not in use. How can I do that?
Here is the code given:
aliases {
displayspi...
I am currently creating and testing a custom board equipped with the nRF9160 and the P822601 antenna. Considering future development, it is expected that another external...
Title: nRF54L05 issue after migrating from NCS 3.0.0 to NCS 3.3.0 with PM static partitions and MCUboot external-flash secondary slot Description: I am migrating a project...
I am currently designing a custom board for my nRF54L15 project and I would like to know if the "Antenna" pin on the nRF54L15 can have a DC path to ground/ground layer of...
I have a nRF54l15dk development board and a custom nRF54L15 board that I am trying to load a Matter Template sample application on. I have created a custom board device tree...
I have observed that when using the ESB protocol at maximum throughput, the measured power consumption decreases as the PHY data rate increases: 4 Mbps consumes less power...
Subject: Connecting LPCOMP CROSS event to TWO DPPI-driven tasks (GPIOTE toggle + TIMER count) simultaneously — only the last-configured one fires
Chip: nRF54L15 SDK: nRF...
Hi Dev team,
My question is related to the charging of the Thingy91 battery through solar panels. I have a solar panel connected to the Thingy on the points TP11 (Vbus)...
Hello, i installed nrfjprog version: 10.14.0 external, JLinkARM.dll version: 6.86f. When i download hex file use nrfjprog -f, there is no log like erase 0xxxxx. How can i...
Hello,
I am facing the following issue:
I am using the blinky sample of Zephyr to control the output of a pin. When this pin is any of the LED pins of nrf5340dk, the output...
Dear Nordic engineers
I study the AES examples.I have a question and would like to ask you.
I study the aes_ctr examples.I found that this program use two functions to...
Hello. I am trying to change the UUID value of a service and characteristic of my nRF52 to have a custom value. I have successfully done this in firmware and it has been found...
Hello everybody,
I am currently working on a project in which I need to read some data from a glucometer. Until last week it was working fine, however I stopped receiving...
Hello,
I installed nRF Connect SDK V2.0.0 using "NRF connect for Desktop"
Now I can't open nRF Connect SDK projects on segger embedded studio.
It showing only VS Code...
Hi,
I'm trying to get a better understanding what causes some unexpected current peaks while nRF9160 is in RRC-IDLE with the NB-IoT mode. I have been experimenting with...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
Hi,
I am trying to run any of the samples, even the most basic ones as blinky, and they will not run on my nRF52840 dongle, which has a header to program directly with jlink...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
Hi,
I am trying to run the sample code for the BME680 sensor over I2C.
I am using the sample code as is; the only modification is my overlay file to define the I2C pins...
