Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I follow description of https://github.com/NordicSemiconductor/pc-ble-driver to build pc-ble-driver from source. But it failed to build it.
cmake \ -G Ninja \ .. -- NRF_BLE_DRIVER_VERSION...
I use the vscode to creat a smp_svr sample project ,and how can i easily add fragment to child image(mcuboot)?
as the picture1, the files overlay-bt.conf overlay-FOTA.conf...
Hi Dev Zone !
I would like to do a complete reset to the ESB communication in my application when there is a problem with it for any reason whatsoever. This is what I have...
Hi guys,
I am currently trying to make my uart work with eDMA functionality.
Up to this point I am able to read using polling, and as second method using IRQ with a message...
Hi,
I am working with NRF52840, I need to read some sensor data or potentiometer data and that will transfer in tablet through Bluetooth. So i need a code for SAADC with...
Hello,
I wanted to develop an Hearing Aid Application using nrf52840. I have downloaded nrf connect SDK but cannot find any samples for using HAP profile. Kindly provide...
Hello,
I intend to read the battery level of the nRF9160. I see that I have 2 alternatives to perform this function, using the AT%XVBAT command or reading the battery...
Hello!
I am working on a project that uses nrf52832 microcontroller with softdevice s132 6.1.1. for BLE capabilities. One of requirements is to implement directed advertising...
Hello,
I am building a product prototype based on nrf52810 with s112 7.0.1 with NRFDK16. So the problem is the memory allocation. I setup the FLASH and RAM as per specification...
Hello,
I'm using an NRF5340 with SDK V1.9.1.
I have a code that toggle one gpio pin on a custom board. It is working well when I use P0.22. However, when I change to P0...
Hi all I have a problem with the sim card on our custom board. Earlier I tested my code on nrf9160dk. But on the custom board, the sim card is not recognized. There is no...
We have an nRF5340 application that builds fine for our custom board. However, it is not very straightforward what steps need to be performed to enable FOTA updates. I have...
I am trying to use DTM to evaluate the output filter on our NRF52840 design. I am using the constant output mode and assume that the physical layer setting is not necessary...
Hey guys,
Recently I have been working with the nrf 52840 dongle and my goal is to use the dongle to communicate with a sensor and read values from it. So far I have been...
