Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello, I'm trying to get nrf5340_audio example running on nrf5340 audio dk.
I'm able to build the code and run it however i'm unable to bond with my mobile phone with android...
Hi! In order to get more accurate battery SOC measurements I need to provide a custom battery model to the app. So, I had to use the nPM1300 EK + Fuel Gauge board to profile...
Our device is set up to provide AT Commands directly to nRF9160 using a USB UART connection and control using a VT100 Terminal simulator. When attempting to connect to the...
Hello. I'm using npm1300ic. In one example, there is a battery_model.inc file related to li-po 3.7v 200 mah battery, and the battery you are currently using is li-ion 3.7v...
When dynamically allocating BLE GATT services and characteristics using custom structures and Zephyr’s dynamic memory functions (e.g., k_malloc, k_calloc), the service registration...
Hello Nordic team, Whilst porting our product from nRF Connect 2.4.1 to 2.9.1 we encountered the following problem. When compiling with ZIGBEE_FACTORY_RESET=n we get Seems...
I'm new to developing nRF devices. This is the first time to set up SDK.
I installed Toolchain Manager v1.2.6 to install SDK, but it is too slow and falls into error. It...
i'm looking for an extremely simple BLE beacon app, which advertises (say) at 1HZ and then enters a "low-power" sleep mode....
there are numerous samples included in the...
Hello forum ,
In here i will upload my project in zip where i m using w25q64 flash -nrf52840 .i m trying to read data of qspi flash read write and read for an two byte(trying...
I am in the process of integrating a custom display driver (ST7305) into my Zephyr-based project and have followed the necessary steps:
Placed the .c and .h source files...
I'm using SDK version 2.9.0 with an nRF52840 in a combined peripheral / central application.
The nRF52840 device starts advertising, but then after connecting (as a peripheral...
Hi,
I am trying to download the nrf connect toolchain in vs code but getting this error
Error: Failed with exit code 1. Failed to download toolchain bundle Caused by...
Hello.
I am developing an application based on IOS-nRF-Mesh-Library, and currently considering porting firmware upgrade function of IOS-nRF-Connect-Device-Manager for updating...
Dear All:
I don't have a le audio enabled phone, and i want to study the hci commands about cis and bis setup up processure.
Could you please provide some HCI logs from...
Hello there!
I'm trying to run the official, unmodified, version of the `WiFi Shell` sample targeting the `nrf7002dk/nrf5340/cpuapp` board and am currently getting:
...
