Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I am working on application code for the nrf9160. Current NCS version is 1.5.1, although I do not think my ancient NCS version is relevant to this issue.
I have removed...
I can't find any documentation on how you are supposed to define partitions in NCS 2.7 when using MCUboot. Previously Partition Manager was responsible for this and was overriding...
Hi,
We have a few questions regarding NRF52832 and NRF52833, please support to clarify for us.
1. Does NRF52832 support Bluetooth 5.4 or 5.3?
2. Does NRF52833 support...
Hii,
I´m working with LTE IoT 4 Click, by Mikroe, that use a nrf9160.
I need to connect to network with my modem, but i have some erros. My goal is to communicate with...
...On a NRF5340, using NRF Connect 2.6.1 SDK and tool chain.
In our application, we need to select if NRF5340 device boots in ZIGBEE ROUTER role or ZIGBEE END DEVICE role...
I've written a custom manufacturing programming tool for ARM Cortex-M4 nRF52832 and nRF52810 devices. It uses a J-Link Plus USB programmer (J-Link V7.98g) and is implemented...
I am working with Zephyr RTOS and I would to prepare one of my RAK4631 with a Zephyr bootloader.
I know that in the RAK4631 documentation we have instructions how to flash...
Hello,
By using nRF Connect SDK v2.6.1, I want to have RTC (Date Time, Calender, etc) functions, so I modified the code based on one of Nordic Academy examples, which can...
Hi,
I've resumed working on my project with the nRF Connect SDK after a brief break. However, when I try to run a simple project, I occasionally encounter an error while...
Hello, I've recently purchased an npm1100-EK schematic from Digikey. The evaluation board works great but I can't find the Schematic & hardware files for this particular version...
Hi everyone. I'm using nRF Connect SDK 2.6.1. I'm implementing LittleFS for file management on an external QSPI-Flash. I need to format the flash and erase all of data. I...
Hello,
I am currently researching the best way to be able to change the rate at which I fetch a GPS fix. I want to start the program at 60 seconds, then depending on environmental...
This is a continuation of this question . It may be necessary reading to understand the context.
I 'm confused by this topic too, however I think the error about "boot_partition...
Hi,
I'm trying to build the MQTT sample for a custom board, trying to communicate between nrf52840 and nrf7002 via QSPI. Here's my board definition:
In the build configuration...
