I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi,
I am using an nRF54L15 and I would like to explicitly enable the HFCLK (32MHz). I want to use it to drive TIMER00, which will run during the whole application runtime...
Hi,
I am now developing a production programmer and I want to know the behavior of SWD and SCK lines when the nRF52840 is in RESET state.
Cheers,
Kaushalya
we are using nPM1300 EVK board for an upcoming project we are trying to interface PMIC PM1300 chip with Ambient Scientific processor GPx10 Pro.
It will be a huge setback...
Hi guys, I have been working with a custom PCB based around the nRF5340 that uses the nPM1100 as the PMIC. I have configured it for 1V8 VOUTB output, fixed VBUS, VTERM high...
Hi
Currently I'm evaluating the nRF54L15 die temperature sensor. I’ve taken a few measurements and noticed something I don’t quite understand yet. Perhaps someone could...
We are planning to use the nRF54L15 for a Matter over Thread product, so we are currently evaluating the low-power performance of this device.
According to the nRF54L15...
We are using a BM833 chip on out PCB. There, we may or may not (config-dependant) interact with a sensor via I2C. We observed (statistically), that using the I2C communication...
I am testing an Auracast setup with a Samsung Galaxy A54 5G and Galaxy Buds2 Pro , where my goal is to broadcast two streams with different languages and select either one...
I want to use a new source LF clock to raise the precision from +-250ppm to around +-20ppm. I already have an oscillator mounted in my PCB, so I want to use it for BLE. I...
Hello, my name is William. I made new Lenovo wireless keyboard dongle firmware using nrf52820 and wrote it to dongle. But at first I connected device using J-link version9...
Hello,
I attempted to rebuild the reference circuitry from the nPM2100, and I am measuring unusual power consumption using the PK2 outputting 1000mV.
Partially, I...
I'm using the MCUmgr + MCUboot solution for BLE OTA FW updates (i.e. CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU).
Is there any way to require pairing for firmware updates? I see...
In the LTE_MODE_PREFERENCE Kconfig description the CONFIG_LTE_MODE_PREFERENCE_LTE_M_PLMN_PRIO option states that: " LTE-M, PLMN prioritized
LTE-M is preferred, but PLMN...
Platform: nRF54LM20A SDK Version: nRF Connect SDK v3.3.1 MCUboot Version: Included in NCS v3.3.1
Background
On the nRF54H20 , the IronSide Secure Enclave provides a...
