Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi connection,
I am trying to build indoor position system, Find the location, Find the direction and Distances project. can you suggest it is possible in NRF5340DK ?
...
I noticed in the nRF extension in VS Code, there are the "pristine build" and "erase and flash to the board" options. I was curious when I should use these options instead...
Hi,
I am currently programming an nRF52 device with the NCS - I am confused about the API for the Zephyr controller, the API for the Bluetooth controller, and the Softdevice...
Hello,
I have the nrf9160 DK version nRF9160 SICA B0A. I have upgraded it to the latest modem firmware version 1.3.2.
I put my own SIM card and added in prj.conf the following...
Hi, I now aply ble_app_uart example for my custom board My board work perfect Some configurations in my code based on ble_app_uart Advertising_interval : 64ms Tx: 0 Some changes...
I am trying to get the example secure bootloader uart working on my nRF52832 development board but I am seeing a lot of TX errors on the RTT log output from the debug version...
Hello everyone,
I have built a product with the nRF52840 that is ready to be manufactured. Connect JTAG/SWD and upload image to each board seems grossly inefficient. Is...
Good day
I am currently developing a system using the nRF52833. A nRF peripheral device needs to be connected to both a mobile app and a nRF central device. The software...
I'm working on an Android app that scans and makes BLE connections. The app scans for devices advertising a particular service. The app uses startScan with a PendingIntent...
Hi,
I am new to this concept. I am trying to implement the nfc pairing connection in nordic nRF52840 but i don't no where to start and how to implement this one. Can anyone...
Hi,
How to configure the following two CONFIG to connect the nRF9160 module to the nRF Cloud
CONFIG_NRF_CLOUD_CLIENT_ID_SRC_COMPILE_TIME CONFIG_NRF_CLOUD_CLIENT_ID
...
MPU6050 cannot calculating the value of 3 axis and the value return is 0. What is problem? How can I fix it ? Thanks for helping me. AD0 open.Adress is 0x68
Here is my...
Hi,
We are evaluating Segger SystemView for analyzing our embedded applications. However, we encountered occasional overflows in SystemView. These overflows are caused by...
