Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hi,
I'm porting a working SPI camera demo from nRF52840 to nRF54L15 and I'm stuck with an issue where the SPIS RX amount is correct, but the received buffer is all zeros...
I have worked a bit with ESB and see that there are functions to get/set a channel, as well as check the RSSI value in the "struct esb_payload" for a packet. Are there already...
Hi, I am using NCS v2.9.0.
I am using sysbuild to build MCUboot and application images. Following are relevant Kconfig options:
mcuboot.conf
CONFIG_MAIN_STACK_SIZE...
Hi, having a little of an issue and would appreciate your support:
When bringing up a board which has the nRF9131 and the nPM6000 I'm getting the following error when doing...
Hello,
Currently working with NCS v3.10 and using SMP service with external flash to store image in a custom board. I'm capable of upload zipped application using DFU button...
I am using the nRF9151 DK, using the Serial LTE Modem firmware from the nRF Connect quick start.
I am planning to use nRF9151 as a serial modem, and connect it to my Host...
Hello
I was attempting to update a pre-production project where we have 2 servers connected to one gateway where the servers send the audio data back to the gateway with...
Hey guys, I want to store sensor data as circular buffer in non volatile memory. I saw https://docs.nordicsemi.com/bundle/zephyr-apis-latest/page/group_file_system_storage...
If a heartbeat or other chunk reliant on symbol file data is ingested when there is no symbol file associated with the Software Version / buildID it seems like the chunk is...
Hello,
I am currently trying to make an application that can do FOTA and store the secondary firmware image on an external flash using sQSPI. The project I started is based...
Hello,
We use the nrfx spis driver for communication between a ST processor (master) and a Fanstel BT840 module (nRF52840).
We have upgraded ncs from 2.6.0 to 3.2.1 and...
I am using a GPIO pin ( P1.05 ) as a reset signal for an external CPU component. The pin functions correctly and stays low when tested in a basic GPIO application. However...
I'm using NCS 3.2.4. When USE_PARTITION_MANAGER is active, the ARM linker script defines ROM_SIZE as PM_SIZE (the full app partition) without subtracting CONFIG_ROM_END_OFFSET...
I have a simple code. send msg to a message queue. and handle the message in another thread. I my old environment ncs2.4.0. I looks works well. // after get msg queue. to...
