Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
I see from the SAADC page of the datasheet that there is an internal 0.9V reference on the nRF54L15, but I don't how this reference is generated. Is it an active regulated...
Environment
My hardware is the nRF9151DK dev kit and a custom board with nRF9151 (Monkeytronics Airsmart Cellular Beta 3).
Using nRF tools and SDK v3.1.1.
Using Onomondo...
I used nrf54L15 chip P2 port's SPI.used spi_transceive_dt tx 10 bytes. but chip divide two process (8Bytes+2Bytes).this result is not my object. code as below:
int spi00_dma_transceive...
Hi, The RebootCount attribute of the GeneralDiagnosticsCluster is returning a FAILURE response.
This issue is causing failures in Matter test cases TC-ACE-2.1. CONFIG_CHIP_LAST_FABRIC_REMOVED_ERASE_ONLY...
Hello,
I'm trying to put the nRF54L15DK into System Off mode, using sdk & toolchain version v2.8.0.
The provided example (\samples\nfc\system_off) works on my evaluation...
Hello, modem_shell sample build throws error “undefined boot_write_img_confirmed” with nRF Connect SDK 3.2.1. This issue didn't exist in nRF Connect SDK 3.1.0. I did a quick...
Hi I have updated th nRF Connect for VS Code Extension Pack to the newest version. But when I want to enter Debug in VSCODE, the error comes out. Before upgrade, the debug...
Hello,
I am currently working with an nRF5340 configured to operate in High Voltage mode , where the main input supply is 5 V .
Issue description
When the nRF5340 is...
I just wanted to notify that I need to set CONFIG_SOC_NRF_FORCE_CONSTLAT=y in order for a NRF54L15 to be able to respond as a SPI slave (SPIS) using nrfx SPIS code.
Otherwise...
Hi,
I have developed custom hardware based on the nRF9151 chipset.
I would like to program the firmware using nRF Desktop (Programmer) with a third-party SEGGER J-Link...
Hi,
I am having trouble communicating between the nRF54L15 and the nRF7002 in a custom board. I flashed the scan sample. I made a new overlay as below:
/*
* Copyright...
Since about a week or two ago, I cannot flash (or debug/reset etc.) my device from the VSCode nrfConnect extension, when more than one device is connected to my PC. I am using...
Hi,
I am trying to confirm whether nRF54L15 as a chip officially supports the UTP OTA feature.
From the SoftDevice Controller documentation I can see that the following...
I am using the Zephyr SPI driver to control a WS2812 LED strip through the SPI interface. Since only the MOSI line is required for communication, I want to configure the SPI...
