Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi Dear
Is the WLCSP package of nRF54L15-CAAA a glass package?
Is it similar to the WLCSP package of 52832-CIAA?
The above refers to the molding material.
If possible...
Hi Nordic
What is the best way to protect against downgrading the APP FW via DFU.
I seems that im able to downgrade even 2 config below are set.
I tested it on SDK...
Hi,
I have two PPK2 units, and under the exact same test environment and PPK2 settings, simply swapping the PPK2 results in completely different measurement results. Which...
Hi all,
I'm trying to combine two NFC messages, I know that I can combine multiple records into one message. But the problem is that OOB_LE message will already contain...
I'm fairly new to Zephyr and initially I'm hoping someone can point me to an example where SMP over UART can be used to update a firmware image slot. Google seems to have...
Dear All,
We need to develop a custom low-level driver for NFC communication using the Hardware Abstraction Layer (HAL) library exclusively . We are currently unable to...
Was able to build after I installed these two packages
/usr/local/opt/python/libexec/bin/python -m pip install --break-system-packages PyYAML brew install pykwalify 2>&1...
I only learned today that the REGOUT0 voltage is changeable, which could be perfect for us, because our power needs changed dramatically.
Our circuit was originally designed...
I ordered a Thingy 91x and am tyring to configure it according to Introducing the Thingy:91 X – The Ultimate Cellular IoT Prototyping Platform on YouTube but I am getting...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
Hello, I'm a beginner and trying to do my project with nRF9151DK. As said this project uses the nRF9151DK that requires high-throughput USB-UART data streaming on two boards...
Hi,
I am new to arm and ble development. I am used to work with AVR mcus and I am trying to migrate a project from AVR to nrf52.
AVR usually has some "General Purpose...
Hello, I would like to evaluate the Thingy 91:X, but I can't install nRF Connect SDK on any machine (Windows / openSUSE) due to various problems. I will try to break down...
Hi,
I'm trying to power the chip on the DK from 5V power supply. I connected the USB connector J3, and switched SW9 to "USB Source". However, it seems that this is somehow...
My design is in alpha test and we just discovered that apparently SPIM allows only one module to be enabled at a time. When a second module (SPIM3, SPIM2) is enabled, the...
