Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
“Why can’t I light up the LED when using the official NRF5340 Blinky example? During debugging, I found the program stuck at SLEEP_IF_ALLOWED(__WFE); in the cpu_idle.c file...
I have a 2 Mbit EEPROM, normally I would configure the overlay as follows:
But the M24M02 eeprom uses 4 addresses to access 4 blocks of memory within the device, 50, 51...
Hello
I've juste came back from holidays and I no longer can do pristine build on my applications (no matter which toolchain or SDK I am using). When I do pristine build...
Hi,
I'm not sure if this is the correct place to report this, but it was not possible for me to report this on the nrfx GitHub page.
I found out that the function nrfy_nfct_...
I'm using nRF Connect SDK V2.7.0 and want to achieve coexistence between Zigbee and IEEE 802.15.4 physical layer on the same Soc. Is it possibel to enable the MPSL feature...
Using nRF Connection SDK v3.0.2 and nRF Connection SDK Toolchain v3.0.2
Create a new blank application, "Add build Configuration" for nrf54l15dk/nrf54l15/cpuapp/ns then...
Steps Taken:
Followed the official Nordic guide for adding DFU support to Thingy:91.
Built the project successfully using west build .
Tried flashing via...
Hi all,
Full debug builds ( -Og ) of lwm2m_client simply don’t fit into the nRF91xx targets (nRF9151 DK, Thingy91, Thingy91x). As a workaround I found that building with...
Hi There,
I'm following the "nRF Connect SDK Fundamentals" to set the environment up. The device I'm using is nRF52 kit with N52832 MCU and PCA10040.
The USB wire is works...
Hello,
I am following the official Nordic Academy nRF Connect SDK Intermediate course , specifically Lesson 9 – Bootloaders and DFU/FOTA, Exercise 5 (FOTA over Bluetooth...
Hi,
I’m using the Thingy:91X board with the nRF9151 chip, modem firmware version 2.0.2, and SDK version 2.9.0.
We’re encountering a serious issue: the modem does not reconnect...
Hi, I am no longer able to download the nRF5 SDK version 16.0.0_98a08e2 using curl . A few weeks ago it worked fine, but now I can only download the .zip file through a browser...
I'm using the nRF9160DK as a BLE-to-LTE bridge, and I have the onboard 52840 configured as my Bluetooth controller. The 9160DK advertises as a peripheral and waits for a connection...
“Why, after setting up the custom board and writing CONFIG_BOARD="my_custom_board" in prj.conf, do I encounter the errors: message(FATAL_ERROR "command failed with return...
I was hoping to access content from DevZone and DevAcedemy content from NotebookLM to combine with my private documentation so I could ask questions specific to my device...
