hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hello team,
We are using nrf52dk with nrf52832 by vs code nrf connect sdk extension.
I have add zephyr led blinky application and flash it on the board and it's working...
Hi,
I like to analyze my custom BLE firmware thread activity, event, and timing using the Segger SystemView application. I have added the following configuration in prj...
Hello,
A super-simple piece of code that enables UARTE1 to receive a byte stream does not seem to work.
It seems as if nrfx_uarte_rx_enable() hangs up.
When I single...
I wanted to check if iOS 18 supports extended advertisements on coded PHY. I am not concerned with the advertisement payload limit but the increase in range that is possible...
I tryed to use the callback function provided by mgmt to hookit, but after including the header file` zephyr/mgmt/mcumgr/grp/img_mgmt/img_mgmt.h `, it prompted that "mcuboot_config...
Hello everyone,
I am currently facing an issue when trying to read data from a block of a Mifare 1K card. After debugging, I found that my program fails to authenticate...
We want to enable 2 way communiaction between Our Nrf9160 devices and server using Websocket secure. We used this as the starting point. We removed anything related to IPv6...
Hello,
We would like to interface an external PSRAM with nRF5340 MCU.
We didn't find any refference on how to do so.
So, my question is it possibel to interface...
Hello,
I'm using nRF9160 and modem firmware version 1.3.6.
I'm using %XRFTEST command to measure RX power received by modem. Command documentation can be found here: https...
I have been through the devacademy lesson on custom boards and am using the nRF53 so have used the custom board for multi-core approach. The example uses the 9151 which has...
I'm trying to add MSC functionality to my project, but I'm encountering the following error:
To understand the cause of the error, I tried creating a new application from...
Hi Nordic Team
We develop a sensor node for a customer based on nRF5340. For now I use a nRF5340DK to do my tests with NCS 2.8.0 (using VS Code).
Based on examples, I...
Good Day,
We have an ongoing project that uses an RP2040 MCU (with FreeRTOS) and we need to add WiFi capabilities to it. It needs to be dual-band and fairly high throughput...
Hi all,
I'm currently working with the nRF52 DK (nRF52832_xxAA_REV3) using the nRF5 SDK version 17.1.0_ddde560 and the IAR Embedded Workbench - Arm 8.32.3 IDE. I'm facing...
