Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
Hi,
I am testing two advertising sets on nrf sdk v2.6.0. Legacy advertising and long range. I tried to modify https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples...
Hello,
as part of my tries to use xip on nrf52840, I found that using the entire program on the external flash is impossible due to Errata 216 .
I check the FICR for my...
Hello,
I am needing to use two separate SPI masters, but I'm running out of pins. Are all of the pins compatible with SPI or are there some I should avoid. I'm thinking...
Hi all,
I have an application that is pretty simple. One master that needs to stream small payloads (sub 32 byte) to a receiving device. The payload is a fixed size and...
Question: nRF9161 Getting the high accuracy oscillator (HFXO) outside and sync with other nrf chips?
Basically I want to get the Clock Signal outside on a Pin, is it an...
We have 1 central device and 4 peripheral devices in which one of the peripheral is mobile device if we connect both mobile and other peripheral devices(nrf52840) the central...
I am testing an nRF9160 devkit with a TMP117 I2C sensor. My current goal is to read values from its registers.
My current code uses the function i2c_reg_read_byte to read...
Hi,
I've just received a nRF52840 DK and I'm trying to build and flash the blinky sample on it but the build failed continuously.
I also tried with other sample like the...
I want to convert raw hex bytes to utf8 format. The nRF5 SDK supported this with help of ble_srv_ascii_to_utf8() api. Is there something similar api available with nRF Connect...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I am planning to set up the system as...
Good night,
I am doing the course "nRF Connect SDK Fundamentals" to learn about Zephir integration with nRF52840.
I am developing a RTOS solution based on the RAKWireless...
Hi,
I have an application that each 30 minutes connects to AWS, sends some data and then disconnects and goes to sleep. I have based my aplication on the asset_tracker...
I am trying to use the nrf5340 audio DK for the first time using one of the sample blink codes. I keep getting an error when first creating an application by copying the sample...
Hi everyone,
I'm a bit lost with the nordic documentation. Here : https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/applications/serial_lte_modem/doc/MQTT_AT_commands...
we have two questions about dfu recover operation on coex_ble&wifi example. because its flash size is so big that it could not be reduced under 500kB. so, we thought that...