hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
It works when I use I2C_2 to communicateon nrf9160. The register value is successfully accessed when i2C_reg_write_byte() is called.
9160dk_9160ns.overlay:
I want...
I am trying to use peripheral/spis as a reference for configuring my nRF52840 DK as a slave. The SPI clock frequency is 1 MHz. The SPI master is another micro-controller....
Hi,
I am using nrf52832 development board with sdk 17.0.2 and S132 softdevice. My requirement is to scan and advertise at the same time. I am using the ble_app_template...
hi,
I am using nrf52832 with ble multilink(nRF5_sdk_16.0.0) example. I need multiple connections with the peripheral at the same time. is it possible to connect multiple...
Hi.
I'm developing application that is needed to include UARTE Interrupt.
I can drive UART interrupt well(not UARTE), but UARTE is not working.
Here is my code...
Hi, I need to send data larger than 16 bytes on a characteristic. I see that the maximum number of bytes I can send using the indicate function is limited to 16 bytes.
...
I am working with:
NRF52840 boards
nRF Connect SDKwith Zephyr
On Ubuntu
Desired behaviour would be:
Establish connection with Codded PHY
After some time disconnect...
Hello,
I'm working on a firmware for a device that is created using ble proximity example. It is power constrain device and required a connection interval of 30 sec between...
Hi Great Nordic Support Teams:
Our client is developing their BLE products with 5340 , and they'd like to use NCS SDK 1.4.0.
They setting up the NCS environment with...
Hello. I have a issue about fstorage.
first, I using S332 SD and SDK 15.3.0 version and 52832.
Init flow is below:
Log enable -> SD enable -> SD BLE & ANT enable ->...
Hi,
SES is not including the extra cmake build options, i tried prefixing "--" as we do it in west build, note that it works west build "west build -b nrf9160_pca10090ns...
I am attempting to create a custom Buttonless DFU application by building on top of the default example from the SDK. Specifically, I am merging the Buttonless DFU app with...
Hello,
I am new to the BLE world. I have a nrf52 DK and using softdevice 7.0.1
I am trying to to flash the basic blinky example.
In debug mode everything is fine,...
Hi, I have a custom board with an nrf52840 onboard I was able to program the nrf52, but then I executed:
% nrfjprog --eraseall
and,
% nrfjprog --pinreset
and the JLink...
