Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi, I took my old NRF52840 DK PCA10056 revision 2.0.1 and tried evaluating it today after few years. I am unable to connect to the target. I have 2 identical boards that were...
Hi ,
We have a device running nRF5 SDK 16.0.0 with SoftDevice S332 (BLE + ANT). We use BLE Central/Peripheral links plus multiple ANT sensors. Under load we see frequent...
Hiya,
I am currently going through the nRF Connect SDK Fundamentals Lesson 2 (section: DK devicetree file) and I am stuck. In the example given, it says:
" These hardware...
It's great to have a public forum with Nordic engineers helping out but the DevZone web experience leaves much to be desired. The editing is painful enough that I really dislike...
We are using nRF54L15 devices and have enabled secure boot . Our current setup is:
Firmware images are signed with a private key
The corresponding public key is...
Hi,
I am trying to use lvgl on nrf54l15, but I am facing issues with spi. I was trying first to use vanilla zephyr 4.1, but now I switched to ncs 3.1.1. I am trying to run...
Hi
I'm using two nRF5340 Audio DK's for my university project. I'm just trying to familiarise myself with the audio examples by sending audio from one kit to another but...
Hello, I am facing an issue of low speed of file read and write while using LFS on External Flash, Winbond (W25Q64JV) .
This is the Configuration Im using in my DTS file...
Hi,
Just received a nRF52840 connected it to my Apple Silicon Macbook (maybe relevant?) which is running Sequoia 15.2 via a USB-C to micro cable.
When I powered it up...
Hello,
Setup:
nrf5340
ncs 2.9.1
Zigbee r23 add-on
I’ve implemented a custom ZCL cluster that acts as a data pipe. I’m trying to determine what the actual maximum...
It would be nice to be able to provision the KMU of nRF54l15 devices directly from the nRF Connect Programmer Tool. This is currently only possible using the nrfutil command...
Hi: Nordic Team
Environment: - SoftDevice: S332 (SDK16), ANT+ + BLE on nRF52 - Calling ANT APIs from app (e.g., sd_ant_channel_status_get, sd_ant_channel_rx_search_timeout_set...
Hello everyone!
I want to use BLE with the filesystem (FS), but I haven’t found any examples. When I enable BLE advertising, any filesystem operations stop working.
(...
Hello Nordic team,
I'm working with nRF Connect SDK (version 3.1.0) on an nRF54L15 device and using mcumgr for Bluetooth LE firmware updates via the SMP service.
My goal...
