We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Just a quick one as I couldn't find it on google. I'm going to implement a beacon like broadcaster but one not based on location. It'll probably be a uuid, a random identifier...
Hello,
I encountered a problem while trying to bond a nrf54L15 (central) with a nrf52810 (peripheral). The firmware of the nrf54 is using Nordic Connect SDK and the nrf52...
Hello,
I hope you are well.
I have a code inside the connection connected callback that sets the MTU to the maximum, which is working fine on ncs v3.0.2 but generates...
Hi everyone,
I’m currently working with the nRF9151-LACA-A1A-R module, developing NTN communication features using SLM mode. However, I haven’t been able to find any documentation...
"I am using nRF Connect SDK (NCS) v3.1.0 and developed BLE DFU functionality by referencing the Nordic Semiconductor Academy course: ' Exercise 5: FOTA over Bluetooth Low...
Hello,
I use nRF5 SDK and nRF52833. Now I want to do the radio test at the "examples\ble_peripheral\ble_app_uart".
When I use radio_test_init(&m_test_config); or other...
I am currently trying to claim my nRF9151DK on the nrf cloud. I went through the Quick Start steps and activated my SIM card but my device has been stuck in this state for...
Hello,
I am currently testing the Matter Closure sample with an nRF5340-DK board. I am using nRF SDK 3.2.0.
- When I send an open command, everything works fine.
- When...
I'm trying to make the basic Button sample work but am having problems.
The physical button is a latching button. Press it and it moves in with a click and physically stays...
nRF52832 Product Specification V1.4, page 344 lists predefined baud rates only.
Is it possible to use other values for custom baud rate, and if so, what is the relationship...
We have noticed an issue with received characters being dropped on the UART shell interface. Originally, we found the issue using our own application, but subsequently we...
I am using a nrf54l10 module on the pcb and using the nrf54l15 dev board. So I have a bootloader, the mcuboot, and then the image. I program over SWD on the pcb. So my problem...
Hello!
What would be the best way to start a custom LE Audio application with a different codec?
I mainly want to evaluate being able to stream 2-4 channels from a 53...
Hi,
I am using the npm2100 as a power management chip in my product, utilizing only the boost function. When only the npm2100 is soldered on the PCB with no load connected...
I am using nPM1300 MIKROE Click with ESP32 over I2C and enter ship mode by writing the required I2C registers from ESP32 .
Observed Behavior
Ship mode command is sent...
