Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
hello Nordic
i am working with nrf 52840 and 52832. using ncs v2.8.0
i am saving a coredump to flash partition and i am using gdb server - client to try to parse the coredump...
Hello,
I'm migrating an ANT+ BPWR application from **nRF5 SDK** to **NCS v2.5.1** but cannot install the sdk-ant module.
**Background:** - Previously used nRF5 SDK with...
Hello,
I send a ticket because I have an issue to access and write files to a SD Card with NRF54L15DK and 3.1.0 SDK and toolchain.
Can you help me please ?
Here is my...
Hello,
we are trying to run Gazell samples on the nRF54L15-DK, but the protocol & board combination doesn't seem to be supported by version 3.2 of the nrf Connect SDK...
We would like to synchronize several Nordic thingys 53. The Approach is to send two timestamps from a central to them (peripheral) via Bluetooth Low Energy with 100 ms delay...
Hi
I try to start with ST7789 display on nRF54L15 and there are bus fault after add LVGL library. The project is building correctly, but stop just after leave bootloader...
Hi,
I accidentally opened and subsequently programmed the PPK-II in Bluetooth Low Energy module startup. The programming didn't complete but resulted in an error. Now...
We are using the nRF9151 with modem firmware v2.0.4 and would like to perform TX RF testing on NTN bands 255 and 256.
TX RF testing is currently initiated using the modem...
I am working on a project where we are sending data to a remote device as fast as possible. The sender will call bt_gatt_write() until it blocks the thread. So it is just...
Dear Sir/Madam ,
I am writing to request a review of the attached schematic. Please let me know if you have any questions, concerns, or suggested revisions.
If possible...
I am in process up migrating a legacy project from SDK v2.4 to v3.2 and going through each revision incrementally to catch all the changes needed to modernize it and maintain...
I have built and flashed both the exercise and the solution. However in both cases I am getting a connected and then disconnected ( Reason 42). I am clueless as to what is...
Hello.
I am currently testing nRF Cloud and encountering an issue. In the "Select a Project" menu, the "Create Project" button is disabled.
Here is some additional context...
I am using SDK 3.1.1. I am trying to use the "sensor get" command with the internal die temp sensor.
In theory, this is all off the shelf software. I didn't write anything...
