I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hello, I've recently purchased an npm1100-EK schematic from Digikey. The evaluation board works great but I can't find the Schematic & hardware files for this particular version...
Hi everyone. I'm using nRF Connect SDK 2.6.1. I'm implementing LittleFS for file management on an external QSPI-Flash. I need to format the flash and erase all of data. I...
Hello,
I am currently researching the best way to be able to change the rate at which I fetch a GPS fix. I want to start the program at 60 seconds, then depending on environmental...
This is a continuation of this question . It may be necessary reading to understand the context.
I 'm confused by this topic too, however I think the error about "boot_partition...
Hi,
I'm trying to build the MQTT sample for a custom board, trying to communicate between nrf52840 and nrf7002 via QSPI. Here's my board definition:
In the build configuration...
Hello everyone,
I Have a LTE reconnection issue after LTE signal loss with SDK 1.3.6. I was doing some LTE connectivity tests by placing the board in a faraday box. After...
Hello! We have developed a custom board featuring an nRF9160 and an ESP32-C3-MINI-1 co-processor, which is flashed with AT-firmware (version 3.2.0.0). Our current application...
Good morning, if I wanted to develop a board with the VM3011 device, where can I find it? It seems impossible to find it as a device in major stores, and I can't even find...
Hello,
I would like to develop a temperature logger which Starts to log temperatures between certain limits
The data is stored until the device has connectivity to the...
Hello,
I know this issue has been discussed extensively in different posts, and I believe I read all of them, but still I can't get it working.
I'm trying to drive...
Hi,
I'm trying to run the i2s output sample from NRF Connect SDK 2.7.0 on the nrf52840 DK, and I'm only getting the clock signal from P1.15, and no signal from any of the...
I'm just a bit fuzzy on how all of the bootloader stuff comes together.
Our application is small (100K-ish), so a dual-bank strategy seems appropriate.
It uses a proprietary...
Hi.
Could you please tell me how to trigger an interrupt when changing the USBREGSTATUS register?
I can monitor the state of this register in polling mode, but I don't...
We used two different packages of 833 and assembled two batches of PCBs. The first batch used the aQFN package, and the radio can operate normally. The second batch used the...
