if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hello NRF Buddies,
My project is based on NRF51822 with SDK version 12.2.0. I am working with Keil till now and planning to migrate to the Segger Embedded Studio.
With...
I am not sure what I am missing in this. This is a custom board so there is no other circuitry on this pin other than a pad to monitor the signal changes with.
When...
Hello!
Regarding the CRC on the nrf52840 the specifications make it clear that the maximum length of the CRC is 3 bytes, We are working on an industrial communication protocol...
Hi
How can I readout the actual timer value on the fly? I use the timer in capture compare mode and like to read out the timer value.
nrfx_timer_clear(&m_pyq5848_timer...
Hi all,
I have set up an nrf52840 as the sniffer to sniff the connections between my custom board and central phone. My goal is to figure out the bottle neck of the ble...
I based my project on the secure wireless uart example in the nrf5 SDK and linked to the precompiled gcc library 802_15_4_lib_gcc.a
I then tried to add multiple entries...
It seems that once we install nRF Connect into VS Code it completely takes over and now when I open any file in VS Code I see all of the nRF connect tabs and controls which...
I'm trying to debug an application however there is no documentation on how to set up the debug.
How come nRF connect is selecting the HEX file. I want it to select the...
Hey,
I am trying to use the Jam Detection Feature of Openthread on my nrf52840 DK. The device is running as coap server with the example code
"simple coap server". I...
Hi All,
I'm using SDK17.1.0 and I have a question about pairing.
I have a project that references the ble_app_bps program, but I don't get pairing notifications when...
Hi All,
I have a question, it seems to be the SES debugger crashed.
My project only uses peripheral devices, my purpose is to combine libuarte with my framework.
And...
I want to send an interrupt instruction from appcore to netcore by using IPC.
Implementation code in appcore:
Implementation code in netcore:
However, in actual...
I have a vendor mesh model that needs to send a custom 8 byte message.
Here are some definitions
BT_MESH_MODEL_PUB_DEFINE (vnd_pub, NULL , 3 + 8 ); <--what is with this...
Hi,
I have a nRF52840 Dongle connected up to an external j-link debugger. I have been using this over the past few weeks with no issues and unfortunately I have managed...
Hello,
We're facing an issue related to the USB IRQ.
I've 2 EVK boards NRF52833 (let's call them EVK_1 (PTX) and EVK_2 (PRX) respectively). One of them ( EVK_1 ) is connected...
