We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Dear All,
We need to develop a custom low-level driver for NFC communication using the Hardware Abstraction Layer (HAL) library exclusively . We are currently unable to...
Was able to build after I installed these two packages
/usr/local/opt/python/libexec/bin/python -m pip install --break-system-packages PyYAML brew install pykwalify 2>&1...
I only learned today that the REGOUT0 voltage is changeable, which could be perfect for us, because our power needs changed dramatically.
Our circuit was originally designed...
I ordered a Thingy 91x and am tyring to configure it according to Introducing the Thingy:91 X – The Ultimate Cellular IoT Prototyping Platform on YouTube but I am getting...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
Hello, I'm a beginner and trying to do my project with nRF9151DK. As said this project uses the nRF9151DK that requires high-throughput USB-UART data streaming on two boards...
Hi,
I am new to arm and ble development. I am used to work with AVR mcus and I am trying to migrate a project from AVR to nrf52.
AVR usually has some "General Purpose...
Hello, I would like to evaluate the Thingy 91:X, but I can't install nRF Connect SDK on any machine (Windows / openSUSE) due to various problems. I will try to break down...
Hi,
I'm trying to power the chip on the DK from 5V power supply. I connected the USB connector J3, and switched SW9 to "USB Source". However, it seems that this is somehow...
My design is in alpha test and we just discovered that apparently SPIM allows only one module to be enabled at a time. When a second module (SPIM3, SPIM2) is enabled, the...
Tried 2 different wires on both Mac and windows pc. The device didn't show up in system information or Device Manager. NRF quickstart does not detect the device. When I connect...
Hello,
I’m trying to enable image encryption on nRF54L. When I enable the encryption, MCUBoot firmware size gets bigger and does not fit into 60kb region. When I set the...
Hi! I have a nRF52840 and an ESP32 and I want to perform a DFU to nRF52840 from ESP32, supposing I have the signed binary file in ESP32. I was already able to perform the...
Situation:
A FOTA job has been deployed in the cloud, so an update is ready and pending for a device.
Questions:
Once a device connects to nRF Cloud, how long should...
Hi,
I am working on developing Locator Tag using NCS fast pair sample code. I have one query here. Is Accurate RTC required for Google FMDN locator tag? If device loose...
