Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
I am trying to run the sample using NCS v2.5.0. This is what happens on the console when I try to connect from the dongle, when running the Test Procedure:
The discovery...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hello,
I recently migrated to SDK version 3.2.0-preview, which supports Matter 1.4.x.
When I use ZAP and add a new endpoint to the light_bulb example under the name Electrical...
Hi I'm trying to communicate with ICM45686 using nRF54H20 and SPI CLK, MISO, MOSI state appear correct but CS pin is not asserting/deasserting following it the scope capture...
Regarding the nRF54L15-DK development board and its use with BlueZ on an Ubuntu virtual machine: After flashing the hci_uart example onto the nRF54L15-DK board, I used the...
I’m working on a project using the nRF54L15 SoC together with the nPM1300 Power Management IC . In my hardware setup:
BUCK2 output from the nPM1300 is connected to the...
Hello, I am facing an issue in nrf52dk (nrf52832dk). Whenever I access i2c0 bus for the controller it works fine but whenever i switched on the i2c1, it starts giving me device...
Hi, I`m working on a custom board. I have been playing around with it for a couple of months, but just recently stumble upon a strange behavior. This is a custom device where...
Hi, I am trying to use the external flash on the nRF54L15 DK with QSPI to perform the zephyr/samples/subsys/fs/fs_sample sample.
I am using NCS v3.1.0 (on Windows if that...
I’m working on a project using the nRF54L15 SoC together with the nPM1300 Power Management IC . In my hardware setup:
BUCK2 output from the nPM1300 is connected to the...
I currently evaluated the use of the "<modem/at_parser.h>" (at_parser module).
Using it with the at-cmd "at+CEINFO?" is very irritating.
I 07.324 : CEINFO: +CEINFO: 0...
Our team is transitioning to the nRF Connect SDK after extensive experience with older nRF SDKs and custom build systems (based on cmake + west + python) integrated with VS...
I would like to know if in mesh device for the comuniation are used all that channel or only the 3 channel that are used for the advertising channel or all the channel 37...
Hi
any one a clue why I see this bar twice?(see attached picture)
Some thing probably went wrong with my previous older installation.
I already reinstaled Wireshark...
I'd like to call a function on the peripheral (by pressing a button or sending a command from the terminal) that performs unbonding from a central. I'm able to bond using...
