Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hello Team,
I AM USING NRF52833QDAA IN NRF CONNECT SDK , IN DATASHEET P1.09 IS MENTION BUT IN OVERLAY FILE OF NRF52833QDAA AT ALIASES PIN P1.09 IS NOT MENTION OR NOT DEFINE...
Setup NRF52840 with SDK 17.1
FreeRTOS tickless idle mode
When we call xTaskNotifyWait and then get the notification then function returns but the result of the function...
Hello, I'm testing the nRF21540 FEM on a custom nRF52840-based board using the nRF Connect SDK.
I’ve enabled CONFIG_MPSL_FEM CONFIG_MPSL_FEM_NRF21540_GPIO_SPI CONFIG_BT_LL_SOFTDEVICE...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
Hello Nordic Team,
we’re evaluating nRF91 for our next product platform (being strong in LoRaWAN since years) and hoped to quickly run some first field trials with the recommended...
We have been using wget to get nrfutil on CI. Today it stopped working. Giving error " ERROR 403: Forbidden " The same link still works on browsers. The link is: https://developer...
Hi,
We're running into a high memory usage issue on an application that is using the nRF5340-nRF7002, multiple sensors on SPI, SDC with littleFs, BLE and WIFI. The WIFI...
Hi,
I'm currently working with a nrf6191 on a custom board using Zephyr and I would like to use little FS as my file system.
So far I've set the configuration and overlay...
Hi,
As the title states, after a while, the nRF7002 fails to connect SSID after a while. It happens either we perform net_if_up/down or not. I suspect the nRF7002 to be...
Hello,
I’m developing a project using the nRF52832 and I’d like to put the MCU into the lowest possible power consumption mode while still being able to wake it up via a...
Hello, checking if I'm doing this right of restoring initial fw for 91X to work with Quick Start v1.2.0. as described here in Get Started, https://www.nordicsemi.com/Products...
I have devices that manually define PDP context 0 in order to set the APN to the required value for the SIM.
Typically, once connected to the network, the IP address gets...
i would like to get MCC, MNC and other cellular data via API. I found lte_lc_conn_eval_params_get() function/API as part of <modem/lte_lc.h> that has the information I am...
i would like to get MCC, MNC and other cellular data via API. I found lte_lc_conn_eval_params_get() function/API as part of <modem/lte_lc.h> that has the information I am...
