Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hi
We use nRF5340, set GPIOs as PDM for DMIC device, and measure waveform as below
The PDM DATA high level will decrease periodically
Is this waveform normal? If yes...
Hi,
I know that pc-ble-driver-py is archived but as there is no real alternative to it, I'm still using this package...
I'm using BLE nRF52840 dongle to connect to...
I am using the nrf52833 with 17.1 SDK and s140_nrf52_7.2.0_softdevice，i want to scan a scannable extend adv packets，
This is what i get in the BLE_GAP_EVT_ADV_REPORT ： ...
# Background
I am attempting to install ble-sniffer onto WireShark for BLE sniffing. I have been following the guide in Link. I have already flashed my nRF52840 USB dongle...
Using Thingy:53, I needed to add the following code to the boards/thingy53_nrf5340_cpuapp_ns.overlay file in order to be able to view the output:
&uart0 {
status="okay...
Hi
We measure I2C SCL falling time is 5.87ns, little faster than spec. 6.54ns ( 20*1.8/5.5)
We use PIN_CNF[n] (Address offset: 0x200 + (n × 0x4)) ID D drive to tune, but...
Hello,
Are there schematics available for the nRF9151DK?
In the hardware ZIP file, I can only find the BOM and PCB files (PcbDoc and PrjPCB), but no schematic files or...
We are trying to understand whether it is possible to use our external flash drive at45db641e to implement DFU and then load the application firmware via Bluetooth. As far...
I want to design a pair of TWS speakers using the nRF5340, but I'm having a hard time figuring out where to start. From what I understand, the unicast server nRF5340 audio...
Hello Nordic Team, I have devices running nRF9160, modem firmware 1.3.6, tied with MNVO SIM card that provide access to multiple operators. Providing an example seems to be...
Hello Nordic Team,
We are working with the NRF5340-QKAA-R7 and need clarification on which physical pins can be used for UART, I2C, SPI, PDM and USB interfaces .
We have...
Hello, I observed that under low-throughput conditions (2 kbps), the power consumption of the nRF21540 combined with the 54L15 (at 20 dBm) is actually lower than that of using...
Using the Zephyr HCI_UART sample, configured and built for an nrf54L15 DK, with version 3.2.1 of the SDK, I get an HCI error 7 (Memory Capacity Exceeded) when attempting to...
Hello Nordic Team,
We are working with the NRF5340-QKAA-R7 and need clarification on which physical pins can be used for UART, I2C, SPI, PDM and USB interfaces .
We have...
