When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
This is my first time developing for Nordic processors. I am using Zephyr 3.0.99 with the nrf52810 on a ublox BMD-330 eval board. I connected a W25X20CL 2M-bit chip via the...
I've got a working nrf52832 application using central role to connect to another peripheral. I also want to enable SMP DFU mode - so the app needs to advertise and behave...
Hi,
I am using sample code v1.8.0\zephyr\samples\net\sockets\dumb_http_server to test USB RNDIS
I did some changes in overlay-netusb.conf gile lik
# USB Device settings...
I'm interested in seeing what the NRF debug adapter does, using Jlink
2022.7.111 - nRF Connect for VS Code
I can't get it selected and the documentation is not very...
Hello I'm trying to get the lower consumption with this EvK in power off mode. I was expecting around 0.5uA but the minimum I get is 1.8uA ~ 2uA.
The measure has been done...
hi,
I have a got a nrf9160dk and also a custom board built on nrf9160. I want to know which programmer to use for nrf9160dk first and subsequently can use it for testing...
Hello Nordic Team,
I was priting logs using RTT _LOG APIs
I can able to see timestamp while printing it
<t: 16775755>, main.c, 295, --------------------------------...
Hello Nordic Team,
I have a question out of curiosity.
BEACON debug prints has been enabled. And I am seeing these prints for every 10 seconds.
Below is the log
<t...
for the NRF9160 I have 256KB for RAM
however, only 128KB are available for my software, since it's defined as nr9160ns
how can I assign the full 256 kB for my software...
I use Nordic BLE Mesh example(Light Switch), I want to implement remote control. The following is the topology map, and the publish & subscribe address(Group address) has...
Using a NRF9160DK. SDK2.0.0. Modem 1.3.2.
I have a problem when setting up a new NRF board to run with MQTT with AWS.
When the setup is running, I get LOG <inf> for...
Hi,
we have a unit that needs to go for conformance testing.
The only external interface we have is the nNR52833s USB port (pins 12/13 on QDAA).
Alternatively can the...
Hello,
We're using a nRF52840 with S140 SoftDevice (v7.3.0) for a Central device but we're having a disturbing issue when scanning: a hardfault occurs less than 2 seconds...
