Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Because of all the provided examples, developing experience has been really smooth but except the merging of usb_dfu and ble_dfu. Therefore Kindly provide an example of the...
nRF Connect SDK v1.6.1
HW - nRF 52832 DK
Host OS - Ubuntu 18.04 LTS
SES IDE Nordic Edition v5.60 with Segger J-Link USB
If I build the Peripheral UART example then...
Hi ,
I had done the user guide on https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.6.1/nrf/ug_matter_configuring.html#ug-matter-configuring , could you please tell...
Somehow it seems the interface MCU of my PCA10040 DK got confused. I cannot use the JLINK to the nRF any more, and the JLINK drive (in Windows 10) does not show up. LD5 stays...
Hi,
1. I want to know the minimum delay time of BLE data transmission
2.How should this time be calculated
Thank you for all your assistance. Kind regards, Peter.Mi...
I want to modify the lte_ble_gateway app (nRF connect SDK 1.6.0) to connect with the nRF52DK advertising through the ble_app_uart (nRF 17.0.2) application. The lte_ble_gateway...
Hello Nordic Devzone,
I am currently attempting to generate 8mhz clock output to a gpio pin on the nrf5340dk. I have found previous posts about utilizing the gpiote, timer...
Dear Members,
How can I find the cause of
<error> app: Fatal error ?
I can't see an error code ?
Is it possible hardware error because voltage surge ? Can capacitor...
When I set NRF_LOG_ENABLED true, the RTT log can be output without any problem, however, the scanning or advertising activity stop immediately.
I found there is something...
Hi,
I am trying to find Get and set the RTC timer api inside Nordic SDK "nCS\v1.6.1\zephyr".
Could you please help me where I can get these api.
Thank You!!
I got up to this stage while trying to evaluate the module...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk_gsg%2FUG%2Fnrf91_DK_gsg%2Fintro.html
There...
Several place refer us to the SoftDevice Release Notes; eg
https://www.nordicsemi.com/eng/nordic/Products/nRF52832/S132-SD-v5/58987
http://infocenter.nordicsemi.com/topic...
Hi,
I have nRF52840 DK with nRFConnect SDK 1.6.99
Compiled and run on nRF52840 boards:
F:\_Develop\ConnectSDK\ncs\zephyr\samples\bluetooth\periodic_adv
F:\_Develop...
NRF_SDH_BLE_OBSERVER(m_ble_observer, APP_BLE_OBSERVER_PRIO, ble_evt_handler, NULL);
What does m_ble_observer stand for ? i don't see any explanation in the whole project...
