Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hi,
I am having trouble communicating between the nRF54L15 and the nRF7002 in a custom board. I flashed the scan sample. I made a new overlay as below:
/*
* Copyright...
Since about a week or two ago, I cannot flash (or debug/reset etc.) my device from the VSCode nrfConnect extension, when more than one device is connected to my PC. I am using...
Hi,
I am trying to confirm whether nRF54L15 as a chip officially supports the UTP OTA feature.
From the SoftDevice Controller documentation I can see that the following...
I am using the Zephyr SPI driver to control a WS2812 LED strip through the SPI interface. Since only the MOSI line is required for communication, I want to configure the SPI...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
I make a ble hid usb dongle with ncs2.0, ble keyboard send keycode to hid dongle, hid dongle send the keycode to computer.
When keyboard send keycode slow, it's work fine...
Using 54L15 DK for testing. Zephyr toolchain & SDK both v3.02. I have been through the DevAcadamy exercise which uses Blinky for its example, now I want to integrate into...
Hello,
I need help regarding flash memory read on nRF52840 device, SDk16, SD=340.
I have using the fds libarary for memory read/write in my code for many years now. However...
Hi,
I'm trying to scan for coded phy devices with the nrf-sniffer application.
Followed the guide and installed nrf-sniffer with the nrf-util.
In Wireshark it works...
We are using firmware 1.3.6 on the nRF9160. During testing, I ran into the reset loop restriction. To quickly get out of it, I issued a AT%XFACTORYRESET=0 command. (We are...
Hello Nordic Team,
I am using nRF5340 DK as a debugger/programmer to develop firmware for the Fanstel EV-WT02C40C module. My goal is to use Wi-Fi (nRF7002) Wi-Fi scan, Wi...
Hello! I am trying to upload the basic applications to the Thingy:91 X from the downloads tab, here: https://www.nordicsemi.com/Products/Development-hardware/Nordic-Thingy...
Hi,
I just noticed that there's another issue with my project after upgrading from SDK 2.3.0 to 3.1.1.
I am using the 802.15.4 radio for low level packet communications...
Hi,
for a project based on the nRF54L15, we are evaluating the new single-slot DFU mechanism.
Using NCS v3.2.1, I am testing the sample available at: https://github.com...
