I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
I'm evaluating the nRF9160-DK with the SOFTSIM feature enabled.
I would like to know if there is a way to tell the softsim to wait for APDU response for more than...
Hi, I have a BLE application where I want to use the device firmware updates (DFU) over Bluetooth. I followed the nRF Connect SDK Intermediate tutorial on how to enable the...
Hello!
I'm using the nRF5340 for a school design project and as such am financially limited to relatively low cost board manufacturers.
It seems that most of these manufacturers...
Greetings,
I'm trying to add an existing folder from a project with its' contents, but it seems that it only adds files that are included in the folders, the other nested...
Hello,
I am currently working with the Nordic nRF9160DK and am using the https_client example from the examples in the nRF Connect via VS Code (on Windows OS), and as far...
Hi,
I have been trying for months now and don't seem to find a way to build a signed app for mcuboot without having to build the whole mcuboot itself.
In the board files...
hi,
I am using nrf9160+NCS v2.6.1. When the CONFIG_SHELL_BACKEND_RTT feature is enabled, the power consumption increases by 80uA. After investigation, I found that the default...
Hi
Built and flashed ncs2.7.0 SLM application at NRF9151 DK. It will log booting log messages and then "Ready" as below.
Before ncs2.7.0, I found SLM application only...
Dear All.
Using, for instance, a peripheral nRF52840 SoC, would it be possible to change in real-time the text string being advertised, among several prerecorded ones, according...
Hi,
I am following the tutorial to implement the serial recovery on nrf52840DK https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-8-bootloaders...
Hello,
Im using SDK 15 ble pheripheral and central uart example on my custom nrf52832 board.
I would like to know how to set MIN_CONN_INTERVAL and MAX_CONN_INTERVAL for...
Hello,
I would like to send a reason code when disconnecting the client (nRF9160DK) and server in MQTT. How can I do this?
It seems that there is no argument to specify...
When I use nrf_dfu_mbr_copy_bl to do bootloader updating, the data is copied sucessfully, but I find some flash data are updated from 0xFE000 and 0xFF000：
The data is the...
I’m working on a BLE-based door sensor project and my focus is to optimize power consumption for maximum battery life. The code I’m using is designed for a beacon using sdk...
