Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi!
Running LTE_BLE_GATEWAY example on nRF9160DK rev 1.1.3 gives "No HCI driver registered" error together with "Bluetooth init failed (err -19)". SDK/Toolset version is...
To preface:
nRF Connect SDK 2.9.0
nRF9151 DK
Windows 11 PC
Hello,
I have been developing in the nRF Connect SDK for a few weeks now so I am fairly new. I have...
When using the distance measurement sample code on my nrf5340 development kits, LEDs 1 and 2 seem to be working correctly, but LED 3 does not light up when connected. The...
Hi！
I'm working on direction finding. I'm using a nrf52833dk as a beacon, a nrf52833dk and a Direction Finding Antenna Board (PCA2005) as a locator for a bluetooth direction...
Hi All,
I recently received a few dev kit boards that I intended to use for a test fixture we are building. I tried to use it in our test fixture which had been working...
Hello, thingy53 qwicc connect shows 3.2V when pwrd on, yet there is 0v from thingy91x when turned on. Is there some other step needed to get 3.2V? thank-you,
Hello there,
Working on bringing up the FOTA feature on the 54L15. I began with the LBS example. I was using the Nordic "Device Manage" to push the FOTA build.
The state...
I've been using the following SPI2S pins and they've been working:
CLK -> P0.16 MOSI -> P0.17 MISO -> P0.19 CS -> P0.18
I want to use SPI1 instead but when I replace...
I have a two fold question, to build a prototype, I would like to know how to get
tflite micro in zephyr build for nRF9151 DK?
Non-Terrestrial Networks (NTN) on above...
I have been using the nRF Connect for Desktop with the Programmer application for several years to attach our end device to the Dev Kit to program our device with no issues...
Hi
Can the device(nrf52832) be used as a BLE Mesh Provisioner and Light Switch Client(such as Generic OnOff Client) at the same time?
I want to develop a device (nrf52832...
Thanks in advanced. Based on nRF5_SDK_17.0.2, I can use i2c with icm42670p normally. Due to power consideration, I need to r/w this imu with spi either to decide which is...
Hi,
I'm developing with nRF Connect SDK v2.9.0 in VS Code. I followed the exercise l1_e1 from the intermediate course. When I debug with breakpoints and the first breakpoint...
Hello there,
I reported this issue in another thread under a different symptom. With more and more testing, it shows it is somehow related to both Android and the 54L15...
Hello.
I need to read IMU data from LIS2DH12 of nrf 52833 which is in DWM3001CDK. But nothing I do initializes sensor... i always receive
<err> lis2dh: Failed to read...
