Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I have just bought a PPK2 and (mistakenly on my part) assumed it must read the Voltage of the output as well (necessary for power measurements). I see now that it doesn...
For a very small percentage of our devices, we sometimes see watchdog reset events that we cannot explain. The only pattern that we see so far is that the watchdog reset happens...
I am currently developing a project using an nRF5340DK and a custom board.
For some unknown reason, the device is being identified as an "Unknown device." The ironic part...
uart_nrfx_uarte.c, uarte_pm_suspend checks some preconditions with __ASSERT_NO_MSG. In my experience that causes unintended and not required crashes. If the precondition is...
I am building my custom PCB with the nRF52840 chip using the Fanstel BT840F SoC. I have designed and fabricated my own PCB. I am able to flash the code onto the SoC only once...
Hello,
While using ai.lab.nordicsemi.com for model training, I noticed that after the training process is completed, the platform generates several performance charts, such...
Hi,
In my board design, I'm planning to use nPM1300 to power nRF5340 and nRF7002; the user has the option to connect or not connect a battery. If I programme the current...
Hi,
We're developing BLE products with the software developed on nRF SDK v3.2.2.
We are affected by the known issue of the SDK: NCSDK-32763: Upgrading firmware may corrupt...
nrf 5sdk + s140 + 52833 I'm currently debugging the time-sharing operation feature for BLE and the private protocol. I've found that after I power on and initialize the SoftDevice...
Hello,
We currently have various products built around the nRF52810 and the nRF52832. We almost always use a PCB antenna very similar to the one on the "nRF52840 Dongle...
Hi, I am working on project to obtain ecg data via bluetooth. But before that I was trying to see whether I could obtain ECG signals serially through nrf52833. And I tried...
Using nrf5340 with nrf70 on a custom board.
I want to use the wifi interface to send raw wifi network packets (both in associated and non-associated modes).
I have the...
Hello Team,
As we have purchased nRF9151 DK from you, we are not able to import the exact SDK required to develop using nRF9151 DK.
Kindly please let us know how we can...
