Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
how to set bt tx power in NCS
I referred to this example "hci_pwr_ctr", but err occurs:"Set Tx power err: -5 reason 0x00", Possible errors are BT_SCI-ERR_SUNKNOWN_CMD。 ...
Running NRF52840 mcu core on custom board using 17.1 SDK
1. Use the nRF Connect Mobile app to connect to our device over BLE
2. Run the dfu uploader to update FW from...
I am planning to modify the SLM application (NRF9161) to load its own certificates for TLS upon startup. This should be doable via modem_key_mgmt functions.
However, NRF5340...
Hello,
After migrating from NCS 1.8.0 to the latest NCS 2.7.0 version, I am no longer able to disable PRINTK , which we previously did to reduce flash memory usage, as we...
Is the nRF 5340 already FCC Pre-Certified ?
When we integrate the nRF5340 SoC within our product, should we need to get our product certified by FCC ? is there any difference...
hi professor,
The npm1300 is used for power management on my borad.When VBAT and VBUS are connected simultaneously, the bulk 2 output power supply varies between 1V and...
Hello,
I used VSCode debug for APP core without any issues.
But I cannot debug NET core because, APPROTECT is turning on. I want to disable APPROTECT persistently for...
Hello,
I freshly installed nRFConnect 5.0.2 in a Windows PC. Installation was fine.
When I start it I get an error:
How can I overcome this?
BR Matthias
I am currently trying to use my nRF52 as a BLE central to connect to a OBD II BLE Device. I am able to use the name scan filters and connect here
After connecting, I...
Hi,
I am Maria from SmarEdns. We need a hardware device that connect 15+ BLU at a time and update firmware. how many BLU connection avaliable in nRF52840 Dongle at a time...
Hi,
I am using fstorage functions in the ANT broadcast RX project.
I am doing the fstorage write function when the ANT device is connected (Inside RX EVENT of ANT event...
Hi
I need to change the default mtu size（peripheral device）, but it always 23，unless phone requeset mtu size.
ncs2.7.0
nrf54L15pdk any peripheral demo
I need this...
Hi
I know , there are several threads on this subject, but I would like to know if there is a sample that works out of the box on the thingy91.
If not, is there an alternative...
Some time i got this error msg
error] [ Client] - Encountered error -105: Command connect_to_emu_with_snr executed for 40 milliseconds with result -105 ERROR: Unable to...
