I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
I am trying to set CONFIG_TFM_BL2 and it seems like it cannot be set to 'y' because CONFIG_TFM_BL2_NOT_SUPPORTED is also set to 'y' in ${prj_name}/build/${prj_name}/zephyr...
I am using the nRF7002-DK to implement a BLE interface. I need to send packets > 23 bytes through a notification characteristic. I am currently using nRF Connect on an android...
Hello, I am using nrf52832 along with S132 soft device and SDK 17.1.0.
Can you please provide me the peer manager api that can list the paired/bonded devices? Also, is...
Hi,
I would like to ask a few things about Channel Sounding (CS):
Is there any recommendation which method (IFFT, PBR, RTT) should be used for reading the results...
Hi
I`m working with an nRF52833.
I've observed that when the module enters DFU mode, the Bluetooth advertising name seems to be limited to around 22 characters.
If I...
I am trying to run the WiFi Station sample, unchanged on a nrf7002DK, but receive the following error: "wifi_supplicant: Failed to add iface wlan0" Complete output as follows...
I’m currently experiencing an issue while trying to install the Toolchain Manager application from nRF Connect for Desktop (v5.2.0) on Windows 11.
Every time I attempt to...
Setup
Hardware: Nordic nRF7002DK as Wi-Fi STA (client) .
AP & Receiver: a Linux PC creates a Wi-Fi Hotspot/SoftAP (NetworkManager/hostapd) and simultaneously runs...
I’m having an issue using QSPI flash with NRF Connect SDK 3.1.1. I have two PCB versions with nRF52840 MCUs — one uses the W25Q128JVEM chip and the other uses the W25Q128JVPIQ...
I want to connect a W25Q01JVZEIM (128MB) NOR Flash ROM to SPI3 of the nRF52833 and implement USB MSC functionality. However, the build fails. It seems the overlay description...
I'm communicating to the nPM1300 eval kit over I2C from an nRf52833 DK (running a fuel gauge application). This works well until I connect PowerUp (through USB) and enable...
Hello to everyone!
I bought nRF54L15-DK for Matter Over Thread developing and prototyping.
Before nRF54L15 I tried ESP32C6 XIAO + Arduino IDE and it worked but it was...
Hey, I have an nrf52840, with lis2dh sensor.
I configured the sensor using the devicetree using the following code
and I change the sensetivity and some other register...
Hi all
I am very new to BLE development and I hope that this question was not asked before in another way.
Is this example also available in nRFConnect with another name...
